The clap switch circuits explained here will toggle a connected load ON and OFF in response to alternate clap sounds? Here I have explained 4 unique and simple designs which can be selected as per user preference.
The article talks about what the title suggests – a clap switch. A small electronic circuit when built and integrated to any electrical appliance can be made to switch ON/OFF through mere hand clapping.
The proposed design when integrated to any of your electrical appliance can be used to switch it ON and OFF simply through alternate clapping of your hand.
The device becomes more interesting and useful because it does not require any external mechanism or device to carry out the specified operations.
NOTE: An IC 555 circuit can never produce an alternate ON/OFF switching for the load. Instead they will work like monostables and switch ON the load only for sometime and then switch it OFF. So please stay away from cheap misleading circuits online.
Main Application Areas
The main application of the clap switch circuits described below is for controlling home appliances like light bulbs and fans.
Suppose you want to connect a ceiling fan with this circuit so that you can switch it ON or OFF with alternate clap sound, you can easily do it, by wiring the fan 220 V AC input through the relay of the circuit.
Similarly, if you wish to switch a tube light or any 220 V or 120 V AC lamp, just wire it in series with the relay of the clap switch.
The following image shows how to connect fan with the relay
The fan regulator can be connected anywhere in series with the wiring.
Any light bulb can be connected with the clap switch relay as given in the folowing figure
How Sound Vibrations Trigger the Circuit
As you must have noticed the clapping of hands creates a loud sound and is sharp enough to move quite a distance.
The generated sound is in fact strong ripples or vibrations created due to the sudden compression of air in between our striking palms.
A mic is connected to the amplifier stage; the sound vibrations made by clapping hits the mic and get converted into tiny electrical pulses. These electrical pulses are amplified to suitable levels by the transistors or IC and are fed to the flip/flop.
The flip flop is a bistable relay circuit which switches ON/OFF the attached relay alternately in response to each clap sound.
The circuit presented here is basically made up of two stages, the first stage is a two transistor hi-gain amplifier and the second stage consists of an efficient flip/flop.
The flip/flop stage alternately switches the output relay driver in response to every subsequent clapping. The load connected to the relay thus also gets activated and deactivated correspondingly.
The circuit may be further understood with the following explanation.
1) Clap Switch Circuit Using IC 741.
The above clap operated relay circuit was provided to me by one of the keen readers of this blog Mr. Dathan.
The circuit is very easy to understand:
The opamp here is configured as a comparator, meaning it is positioned to differentiate the slightest of voltage differences across its two inputs.
When the clap sound hits the mic, a momentary drop of voltage is experienced at pin#2 of the IC, this situation raises the voltage at pin#3 of the IC for that instant.
As we know, with pin#3 at higher potential than pin#2 makes the output of the IC high, the condition puts the output of the IC go high momentarily.
This high response triggers the IC 4017 pin#14, and forces its output to either move from pin#2 to pin#3 or vice versa depending upon the initial situation of the outputs.
The above action switches the load accordingly either to ON or OFF position.
The above 12 V clap triggered switch circuit using IC 741 was successfully tried and tested by Mr. Ajay Dussa. The following prototype images for the same were sent by Mr. Ajay.
The PCB design (track layout) for the above can be seen below, as designed by Mr. Ajay:
2) Clap Switch Using Transistors or BJTs
In the above explanations I have explained a simple clap activated switch circuit which incorporated an IC for implementing the desired ON/OFF toggling actions. The present design uses a different principle and utilizes only transistors for the above triggering actions.
Clap Switch Video Demonstration
Parts List
- R1 = 5k6
- R2 = 47k
- R3 = 3M3
- R4 = 33K
- R5 = 330 OHMS
- R6 = 2K2
- R7 = 10K
- R8 = 1K
- R9, R10 = 10K
- C1, C4 = 0.22uF
- C2 = 1uF/25V
- C3 = 10uF/25V
- T1, T2, T4 = BC547
- T3 = BC557
- All IC diodes = 1N4148
- Relay diode = 1N4007
- IC = 4017
- Relay = 12v / 400 ohms
How it Works
The figure above shows a straight forward two stage sound activated switch.
The first stage comprising T1, T2, and T3 forms a hi-gain common emitter amplifier configuration.
A mic is connected at the base of T1 via blocking capacitor C1.
Strong sound vibration hitting the mic is instantly picked and converted into tiny electrical pulses.
These are in fact small AC pulses easily make there way through C1 into the base of T1.
This creates a kind of push-pull effect and T1 also conducts in the corresponding way.
However the response of T1 is relatively weak and requires further amplification.
Transistors T2/T3 are introduced exactly for this and help to improve the voltage peaks created by T1 to appreciable levels (almost equal to the supply voltage.)
The above voltage pulse is now ready to be use for toggling the relay ON/OFF and is fed to the relevant stage.
IC 4017 as we all know produces sequential shifting of its output pin-outs (logic high) in response to every positive pulse at its clock input pin 14.
The amplified clap sound voltage pulse is applied to pin 14 of the above IC, this flips the output of the IC to either a logic high or a logic low depending upon the initial status of the relevant pin-out.
This triggered output is appropriately collected at the diode junctions and used to toggle a relay through a relay driver transistor T4.
The relay contacts ultimately goes to a load or an appliance which is correspondingly switched ON and OFF with every subsequent claps.
Using BJTs and Power Supply
Looking at the circuit diagram we see that the entire circuit has been configured around ordinary general purpose transistors.
The functioning of the circuit may be understood with the following points:
Transformer X1 along with the D1 and the capacitor C4 forms the basic power supply circuit for providing the required power to the circuit.
The first stage which includes R1, C1, R2, R3, R4 and Q1 form the input sensor circuit.
The next corresponding stages consisting of Q2 and C3 form the flip flop stage and makes sure that the signals from the input sensor stage is appropriately converted into alternate toggling of the output.
The output stage consists of a single transistor Q4. It is basically configured as a relay driver stage for translating the alternate ON/OFF actions from the previous stage into physical toggling of the connected load across the relay terminals.
The design is very old, I built it in my school days by assembling a kit. The circuit diagram using transistors is shown in below:
Parts List
- R1 - 15K
- R2,R5,R12- 2m2
- R10, R3 -270K
- R4 - 3K3
- R6 - 27K
- R7,R11 - IK5
- R8,R9 - 10K
- R13 - 2K2
- C3, C1 - 10KPF Disc
- C2,3 - 47KPF Disc.:
- C4 - 1000uF/16V;
- Q1,2,3,4 - BC547B
- D1 - 1N4007
- D2,3,4,5 -1N4148 _
- Xl - 12V/300mA Transformer .
- MIC - Condenscr Mic
- RLY — 12V Single Charge over relay
Another version of the above can be seen in the following diagram:
3) Double Clap-Clap Switch Circuit
All the clap-on switch circuits explained above have the ability to operate only with single alternate clap sounds.
This feature makes the circuit vulnerable to external sounds which might occur occasionally triggering the connected load with the circuit.
A double clap operated circuit thus becomes more suitable and resistant to spurious triggering due to the fact that it would toggle only in response to two subsequent clap sounds instead of one.
The explained circuit is simple yet effective and does not employ microntrollers for the implementation unlike other circuits on the net.
The circuit has been tested by me, but it is a fairly complex design it's important to first understand the stages convincingly, and then build it to avoid failures.
Circuit Operation
The proposed clap-clap circuit or double clap circuit functioning may be understood with the following points:
The lower stage is basically a simple sound activated switch circuit which would activate with any loud sound.
The IC 741 is rigged like a comparator with its pin#2 referenced at some optimal fixed potential determined by the setting of the given preset VR1.
Pin#3 of the IC becomes the sensing input of the IC and is connected with a sensitive mic.
The adjoining IC 4017 is a bistable stage which activates the connected relay driver stage and the load alternately in response to every positive high pulse at its pin#14.
When a loud sound such as a "clap" hits the mic, it momentarily grounds pin#2 of the IC741 resulting in a momentary high pulse at its pin#6.
If we connected this output to pin#14 of IC4017 would have resulted in an instant toggling of the load with every single sound input which we don't want here to happen, therefore the response at pin#6 of IC741 is broken and diverted to an IC 555 monostable stage.
How IC 555 is Configured
The IC 555 circuit is rigged in such a way that when its pin#2 is grounded, its output pin#3 becomes momentarily high for some period of time depending upon the values of the 10uF capacitor.
When a sound hits the mic, the high pulse from IC741 output triggers the BC547 attached to pin2 of IC555 which momentarily grounds pin#2 of IC555, which in turn put its pin#3 high.
However the instantaneous high at pin#3 of IC555 takes a while to reach the connected BC547 due to the presence of the 33uF capacitor.
By the time the 33uF charges and switches ON the transistor, the potential at the collector of the transistor is already gone due the absence of the clap sound which happens only momentarily.
However with the application of the immediate subsequent clap provides the required potential at the collector of the transistor which is now allowed to the reach pin#14 of the IC 4017.
Once this happens the relay driver triggers or deactivates depending upon its initial condition.
The toggling of the load thus takes place only in response to a pair of clap of sounds making the circuit reasonably foolpoof.
Another Double Clap Switch Circuit
High pitched sound generated by clap of hands, click of fingers and a various other methods can be used to trigger the next circuit.
The design necessitates a minimum of two intense clap sound pulses to initiate the triggering.
This significantly minimizes the chance of unwanted haphazard switching of the device, due to spurious accidental sound.
The first sharp hand clap is detected by the electret microphone and is fed into operational amplifier ICI's inverting ( -) input at pin 2 via C1.
The signal negative peak at the pin 6 output of IC1 subsequently activates 555 timer IC2, that is set up like a monostable multivibrator.
The trigger signal reaching the pin 2 input of IC2 is internally extended to toggle the dual D flip-flop IC3. With the help of the three-state counter configuration of IC3.
Not one but two sharp clap sounds are necessary to create a positive output at pin 1 that causes Q1 into switch ON. When Q1 activates the relay and switches its contacts to N/O points.
Any electrical appliance attached to the relay's contacts now switches on.
As soon as pin 1 of IC3 becomes high, it continues to be in that situation until a subsequent two powerful hand claps hit the MIC to repeat and revert the condition.
Thus, it requires two loud sound inputs to switch off the electrical load hooked up to the relay's contacts after the circuit is activated.
PCB Design and Component Overlay
Part List
With over 50,000 comments answered so far, this is the only electronics website dedicated to solving all your circuit-related problems. If you’re stuck on a circuit, please leave your question in the comment box, and I will try to solve it ASAP!
Can you make a circuit to make a sound by buzzer when it hear two claps with in two seconds, (limitations -> we can use only one 555 timer and can’t use any other IC’s)
It may be possible by adding a transistor stage with 555, but the 555 output will be ON only for a few seconds, depending on the monostable RC values, and then toggle off, you cannot get bistable action in this circuit.
Ok I am trying to design the circuit and it still tricky.
Please let me know if you design the circuit in Multisim or any other software and it will be helpful.
I draw my schematics on Microsoft paint software.
Sir I reproduced his schema with Kicad. When checking the electrical rules I get the error: Input Power Pin not driven by an Output Power pins Pin 8 VSS 4017
Should I discard it? Thanks
Hi Rosario, it may not be possible for me to suggest on the Kicad problem…but if you build the circuits practically I can assure you these will work perfectly and if there’s any issues I can solve them with a step by step troubleshooting.
I try to post the problem in the Kicad forum.
Can I show your schema? Do I have your authorization?
Sure, you can post the diagram, if possible post the article link also so that the forum visitors will know from where the diagram is taken.
Sir can I get proper circuit working for clap switch using bjt and power source.
Paresh, transistor circuit is already provided in the above article, you can refer to the following design:
Hi,
can you make & give a clap circuit to work on 9v battery, for 5mm – 5 leds (4 white & 1 RGB)
Hi, do you want the LEDs to switch ON/OFF with every clap, or just momentarily ON with every clap?
Thanks at Engr. Swaggatam.
Can the circuit use another source of power apart from battery ?
It drains battery easily .
Should I make a 9 volt power pack ?
Hi Ikenna, you can power the above circuits with a 9V or a 12V AC to DC adapter.
Hello Swagatam, its me Bios, the circuit looks so cool but the resistors 33k and 330 ohm are difficult to get, which value can I use instead. Sir
Thank you Bios, Those values are not critical, slight difference will not have any effect on the working of the circuit. Alternatively you can try connecting assorted values in series and parallel combination to get the actual values of the parts.
Hi, thx for thoses circuits, utiles projects as always 😉
Can I use IC TC4001 ,or IC TC4011, or IC TC4019, or IC TC4020, instead of IC 4017??
I would like to know because, those are the model I got a disposition.
Thx you.
Hi, thanks, do those alternatives have a sequential response to input clocks? If yes then they can be used. I think 4020 is OK, but not 4001, or 4011
Thx you, but wow, your question is a bit complicated for me. I guess I ll go with 4020, and hope it works ))
No problem, you can use 4020
Hi, First, thanks for the circuits.
I want to do the doucle clap circuit using a LM358 so
1- can I power it using a 9V Battery? I don’t have symetric power supply
Also, as the LM358 has 2 op amp, then
2- can I use one part of LM358 for an non-inverting amplification then one part like a comparator? Or is the amplification useless?
The mic will be at 1,5meter of the circuit meaning there will be some loses.
Hi, thanks for liking this circuit.
You can power it from 9V battery but the relay must be also rated accordingly so that the battery doesn’t drain quickly.
No extra op amp is required, since the first op amp itself will be sufficient for amplifying the MIC, even if it is wired at some distance
Please Sir could you guide me to use it as a final year project work?I needed a clapswitch to be made with a password such that only the owner have access to use it.
Lawal, how would you use the password with the clap switch?
Please Sir, I assume by combining a four
output clapswitch with a four key password switch, with the clapswitch changing its outputs with upon a single clap and each changing output activates the password switch. The password switch are numbered in a written form .So by varying the number of claps to activates each of the different
four keys of the password switch, for example 2,4,1 and 3 orderly but successive number of claps needed to activate the four keys of the password switch to activate the clapswitch
It is possible but will require 4no IC 4017, and 4 small SCRs, and other parts.
Thank you Sir, I am very grateful for your response. Please Sir could you send me with the design to experiment on.I needed build it as my final year project work.
Hello Lawal, I have designed the basic first stage, once this is confirmed by you, you can replicate 3 more similar stages with slight different modifications:
The RC diode network shown at pin#2 should be repeated at pin#7 also.
This stage is for 2 claps code.
The circuit is supposed to work in the following way:
When two claps are made relatively quickly, the 4017 output logic reaches at pin#4. Here the user has to wait for a few seconds until the SCR gate capacitor charges fully, and the SCR latches to switch ON the next 4017 IC.
Now suppose the person who does not know the 2 clap code for this first stage, he will try to clap quickly, moving past pin#4 and reach pin#10 of the IC, which will cause a permanent latching of the IC due to the connection of pin#10 with pin#13.
If the person tries to clap with delays, then the logic at pin#2 will cause the 100uF to charge and send a positive pulse to pin#15 of the IC which will keep resetting the IC back to pin#3.
Suppose the person claps initially quickly and then stops at pin#7 then again the circuit get reset due to the relevant RC/diode network.
The same concept will need to be repeated for the other subsequent IC 4017 with the other specified code numbers, accordingly.
Hi,
I’m trying to make a bass drum flash (a 230v 30wLED that lights up only when i hit the drum and then turns off) is it possible to do this with a piezo transducer and a solid state relay? As follows:
—— -12vDC —>|———–|| | S.S.R.|
—— +12vDC—>|———–|<——————-• L
Am i missing anything?
I am awaiting your answer.
Thank you for your time!
Hi, it is possible, but the solid state relay is not required, instead a transistor driver will be enough:
hi, sir i designed the second circuit which requires transistors… i assembled all component on my Vero board, i’m using a 9v battery with a 12v relay. my problem is once my circuit comes on, my LED come on too and if i make a clap it doesnt go off, pls sir i need a response to why its not responding and i’m connecting directly to my 240v light blud.
i would be glad if you reply me
thanks
Hi, as you can see in the video the circuit works perfectly and there’s hardly anything complex in the second design.
You can remove C2 and check the response again….C2 is for delaying the switching OFF action of the relay and the load.
thank you sir, but i have one more question. is it necessary for the led on circuit board to turn off when you clap?
The LED must turn ON momentarily when you clap…please see the response of the red LED in the video
Mine is comes ON, when i attach my 9volt battery. And if i clap i won’t go OFF.
Is there an adjustment i need to make
Although impressive thumbs up, but it seems that 4017 can be removed from this circuit without losing the 2 clap on – 2clap off function. Don t u think so ?
Thank you! without 4017 the output will not lock ON/OFF, it will be momentarily ON and then switch OFF
Dear swagatam
Double clap switch is working from circuit’s near.What can i use about improving distance for mic?(I adjust trimpot) Is mic amplifier just enough?
Glad you could make it successfully. You can try the transistor circuit and replace the 741 circuit with it. Use the T3 collector to feed the transistors of the IC 555 monostable. Ignore the relay at T3 collector
It works but very sensitive i want adjust sensitive what should i do?(using pot?where?) i tried extended charging time(using 47uf it gains to me 2m 30sec ,4.7uf gains 15sec)
You can try adjusting (increasing) the series resistor which is connected between the MIC and the positive supply
Have you tested the double clap switch….my is not working…
It will work, if you do it patiently and stagewise. You will have to separate the upper and lower stages, and test them separately, also you will have to connect a few LEDs across some specified points which will provide you with a clear indication regarding the sequential operations, and help you to optimize the timing for the two claps….possibly I may update the modified diagram soon
Hello sir,
To be more precise,
1. On idle, the circuit when powered, must keep the load shut until we clap.
2. Upon a single clap, the clap switch circuit should respond but should hold the relay ‘ON’ and the load should operate without interruption.
3. Now, by clapping again, the load must not go off rather we will manually shut the load off using a switch against the load.
This circuit is a bit different in operation, i have stressed on “by clapping again, the load must not go off” please keep this in mind.
I hope you understood now requesting you to help me.
Thanks
Hello Sherwin, guess why I told you to add the 1K resistor for C2? It is to latch the relay on the first clap, and I also suggested that to reset the circuit you must short the emitter/collector of T1.
So it is exactly as per your requirement.
Good morning Sir Swagatam,
One small request, could you please link me to the page of a particular clap switch circuit where,
1. upon a single clap the clap switch circuit responds and the load operates.
2. to switch off the load, we will manually control an on/off switch.
I hope you understood, i want a one way clap switch circuit which only will trigger the load (ON) one upon a single clap action and to switch off the load we will physically control the switch to (OFF).
Please do help me with the appropriate circuit,
Thanks,
Hi Sherwin, you can try the first circuit from this article:
https://www.homemade-circuits.com/simplest-sound-activated-relay-switch/
just replace C2 with a 1K resistor.
..to reset short the collector/emitter of T1 manually
Hi sir. I made the 1st circuit using IC 741 but i doest work. I only connect two pin of VR1 1k. Is it correct? I cant fine the problem. Plss help me. I can send you my circuit photo if you want. Plss reply ser
Hi Arnold, it is a straightforward design and will work. You can use two pins of the pot, but the center lead of the pot is compulsory among the two leads.
I would recommend a preset and not a pot because adjusting a pot can’t be accurate.
You just have to adjust the preset such that the voltage at pin3 of the op amp is slightly lower than the voltage at pin2. You can also a add a red LED in series with R4 to check the output response from the op amp to clap sounds
I would like to thank you for clap circuit 1). I am a hobbyst and tested it. As I had lm301 used instead 741. Please inform if lm 301 can be used without any other changes in components.
Rgds
Thank you, yes it can be used, in fact any op amp or comparator IC will work here!
Hi Sir my name is Francis
Having combined the first circuit With 1 microfarad capacitor to pin 4 and ground, 10K resistor in series to pin 6 and 14, 10K resistor in series to pin 4 and 15 and 0.22 microfarad 50V capacitor to pin 15 and positive.
How much current does the circuit use?
Hi Francis, the circuit may consume 10 to 15mA when idle, and upto 50mA while the relay is operational.
1.Sir how can i further increase the sensitivity of the mic and can i use two micro phones or ill need to add or remove a component
2.Sir all the components plus the new new resistors and the capacitors plus the relay.maximum current is 50mA. Can a use a 9v1A power supply or any other please advise!
Thank You
You can tweak R1 value to adjust the sensitivity of the circuit.
You can connect two MICs in parallel.
you can use 9V 1 A supply, just make sure the relay is also rated to work with 9V
1. Sir if I’ll use two microphones do i need to change the value of the variable resistor?
2. Sir I tested the first circuit with the given components but the LED (ON) connected to the transistor would light first instead of the other LED (OFF). If I add a 1uF/25V, 0.22uF/50V and two 10K resistors just as you’ve explained to someone else above this problem will be solved? Please advise…
Thank you
Francis, for two mics also the circuit will remain the same.
Which two LEDs are you referring to, I can see only one LED in the first diagram?? Where did you connect them?
I tried everything but it doesnt seem to work
i think the transistor circuit works perfectly
coz the LED goes off after 2 seconds
but the relay doesnt seem to work
what could be the problem? which part of the 4017 circuit is important for the relay? i mean which parts do i need to check first?
I hope you have built the 4017 exactly as shown, with the 1N4148 diodes?
OK, now connect an LEd in series with the base of the relay transistor. This will quickly tell you whether the signal from the IC 4017 is correctly reaching the relay transistor or not. If the LED switches ON OFF but the relay doesn’t will mean the transistor is faulty. If the LED does not respond, short circuit the emitter/base of the relay transistor and check again, if now the LED responds then again it will prove the transistor is faulty.
I can’t anticipate any other fault right now, except if the IC 4017 itself is faulty,
Hi there
I could not find a bc547 in the market
i know its very common..its strange it wasnt available
anyway what is the best sub for it? i have plastic 2n2222 , bc546, bc 548 and bc 549
among these which one do u suggest?
He electron, You can use BC546 which looks most appropriate among the mentioned devices.
Hello sir
How you doin?
I have a question
How much mA does the second circuit need to work?
Hello Nikolas, it will consume around 5 mA when the relay is not active, and around 50mA when active (or depending on relay specs.)
in reply to “Both will work, you can use any one of them”
yes but which one would u suggest?a 2.2k pot or a 4.7k pot?
There will be no noticeable difference in the response, so I don’t have any specific suggestion, you can use the one which is available with you.
I just built this circuit
I used a 12v adapter as the supply
When I whistle the leds turns on and it goes off once I stop whistling
Also the 12v relay does not seem to turn on and off
I know there’s something wrong
I just don’t know what
Can you help me plz?
It won’t respond correctly to whistle sound, it is designed to respond to low frequency loud sounds, like a clap sound.
You can try momentarily bypassing the emitter/collector of T3, and check if the relay responds or not. If it doesn’t respond then your 4017 circuit may be having problems, which you’ll need you troubleshoot by examining the connections
What if I’m the relay responded when I connect the e and c of t3?
Wait please ignore my last message
I didn’t get what you mean by bypassing the emitter or the collector of T3
U mean connecting base to emitter? Or collector to emitter
it’s emitter and collector, not base….in other words Connect pin14 of IC 4017 with positive line momentarily, tapping it alternately should click the ON/OFF
the second circuit as you said has more sensitivity. but i cant see a pot on it
i wish there was a pot so that we could adjust the sensitivity
you can use a pot for R6 or controlling sensitivity.
THANKS A BUNCH
A 2.2k pot?
It will do, connect the center terminal with the base of the transistor.
should I use a 2.2 pot or a 4.7? which one works better sir?
Both will work, you can use any one of them
is the positive of c2 connected to r4 or it is a jump?
It is a jump, connected only to T2/R5…you can remove C2 because it will create a delay OFF on the load
C2 the 1uf cap? So if I remove the 1uf cap the relay will go off once I clap?
yes, if you remove C2, relay will quickly respond to your claps, if C2 is included, you will have to pause for 2 seconds between each clap.
Hi.I want to make the first circuit
To get more safety Im planning to use a fuse for my 9v 300mA power supply.what fuse amperage do I need? 0.5a fuse or 0.3 or…? can I even use 1.6A fuse? will it cut the AC if the power supply is shortened?
Hi, a fuse is actually not required, and the chance of your power supply getting shorted is almost zero. Still if you are interested you can put one on the AC side of the power supply, the rating will depend on the load or appliance that you connect with the relay contacts. If it’s a 0.5 amp lamp then the fuse could be rated at 1 amp and so on.
hi sir…i really like your website
i always come here for %100 working circuits
i have a question about the circuit above
the first circuit
what is a good replacement for the 741 ic
i have TL081, TL061,TL071
Ive heard that the TL071 opamp is a low noise amp which i think does affect the circuit’s sensitivity right? but i dont know for sure if it can be replaced with 741 with no problem
the reason im looking for a replacement is i could not find a 741 ic at store
Thanks oppa, I,m glad you liked my site!
You can actually use any op amp for this application. The low noise characteristic is not relevant to this application, since it is used only as a basic comparator, so basically you can use any op amp here, all will work
single clap circuit work flawlessly. I can adjust the sensitivity by ajdusting the pot or the aupply voltage.
that’s great, I am glad it’s working!!
hello sir
i am very interested in this project
i want to make this circuit for my bedroom light…can u plz tell me which circuit has more range and sensitivity?
and about the second circuit…can i supply it with 9 volt power supply and replace the 12v relay with a 9v one?
the 4th circuit looks nice.. does it work properly? no offence…in my country these components are expensive
Thanks Hobbyman,
The second circuit seems to have the longest range and high sensitivity. Yes it can be used with a 9V power supply and relay.
The 4rth circuit is yet to be tested but I am sure it will work once everything is adjusted perfectly.
Ok sir thank you
So in the second circuit, I can use 9v supply and 9v relay or 9v supply and 6v relay?
I’ll be back soon with a pcb so that it users who would prefer a pcb can use it
And I saw u said something about adding a 0.22 cap across pin 3 and 6 in order to get extra sensitivity, should I add it to my pcb?
Hobbyman, I referred to this circuit not the first one:
This circuit is more sensitive.
For 9V supply you must use a 9V relay, not a 6V relay
hai Iam vishnu, sir I bulid a clap circuit using Bc547transistors without any Ic their are 3 transistor of Bc 547 and1transistor BAc368 without relay my circuit is completely worked first after some type it is not detect sound instead when we touch mic the LED wil ON&OFF .
Vishnu, if you have built it on a breadboard then possibly there could be a loose contact somewhere, otherwise one of your transistors could have gone bad…BC547 are rated at minimum 60V so those may be fine but BC368 is rated at 20V only so may be you could test this transistor….and if you are using a relay make sure to use a freewheeling diode across the relay coil
I tried doing this project in breadboard but it doesn’t respond to my clap or any sound i made. the LED only lit, that’s it. what can be the possible problem in this one? I hope i could get a quick response, it is for our electronics project. Thank you and good day!
first of all recheck all the connections, because breadboard are always prone to mistakes and loose connections.
if possible remake it on a veroboard by practical soldering.
If you are referring to the last circuit, remember the preset has to be adjusted carefully to get the results, otherwise the circuit won’t respond.
for testing the IC 741 response, remove the LED/resistor from the IC 4017 pin#3 and connect it across pin#6/ground of the IC 741.
Now after careful adjustment of the preset you should be able to see this LED becoming momentarily ON on each clap sounds.
YES IT WORKED,after a long time.Thank u for your instant reply.It is only because of your fast reply i could make it successfully.Now i have to make another project-amplifier circuit.Please suggest any website for this project which uses an ic,condenser mic and a 8ohm speaker(or any small speaker).
I am glad to know it worked…congrats on that!
for MIC amplifier you can try the last diagram as given in the following article
https://www.homemade-circuits.com/2012/08/ic-lm-386-datasheet-explained-in-simple.html
I made it but when i connect the power supply,8050transistor near the diodes is getting heated and the circuit is not working.Please tell me where is the problem in my circuit.I have used the first circuit.
In the first circuit it's BC547 near the relay, anyway even if 8050 is used it should not become hot…unless the relay coil is shorted, or you have done something seriously wrong with the connections.
make sure you have connected the transistor pinouts correctly.
Can i power the second circuit with a 12v supply?
yes you can
If i connect the relay to an appliance and clap will the applianceremain turned on untill i clap again.
Thanks in regards.
yes, the appliance will remain switched in the same position until the next clap is made….
For the first circuit or second or will both the circuits work in the same way as you have replied above.
Thanks in advance.
yes that's right, because both have flip flop stage…
sir, as u said to connect 10k at pin 4 n 15 of ic 4017 and capacitor to pin 15 and +vcc .
the circuit work correctly as led at pin no 3 of ic 4017 glow before clap and after clap the led connected to transistor glow, but this happen only one time, after that circuit stop working none of led glow, now what should i do?
Prashant, you can try putting a resistor 10K in series between pin#6 of IC 741 and pin#14 of IC4017, and connect a 1uF/25V capacitor across pin#14 and ground.
also for better reliability configure the output of the 4017 exactly as done in the first diagram.
can can u tell me the exact value of pot for perfect result?
Sir can you tell me that we can use this circuit to automatically open the door??
Sir can you tell me that can we use this circuit to automatically open and close the door??? Please reply as soon as possible.
If yes then how?? What changes should be made in the circuit??? I have to submit a project proposal and my project is "automatic door opening using clap switch" and the circuit should work from the minimum distance of 8 feet.
Please help me…!!!!
The door is not of the full size. There is a mechanical model of wood of almost 1 feet tall.
sir, when i apply 9v to the circuit which led sholud glow by default i.e.before clap, the one which is connected to pin no3 of ic 4017 or the led connected to transistor
pin#3 LED should light up… but sometimes it might not because the logic high might disappear across one of the other outputs of the IC 4017….so to prevent this please connect a 10K resistor between pin#15 and pin#4…and also connect a 0.22uF capacitor from pin#15 to the positive rail.
sir any minor changes can made to second circuit that lead to more sensitive and responce small sound genarated by clap. now I was still struggling to adjust 1k preset as you said above. thanks
you can try connecting a small value capacitor across pin6 ans pin3….this should improve the sensitivity of the circuit manyfolds
still the 1K perset adjustment will be crucial.
sir small value capacitor means which capacitor can i use and does it has polarity
preferably it should be non-polar…you can try a 0.22uF, or a 0.33uF etc
sir i bought 0.22uf capacitor but it has polarity then which side to connect #pin 3 and #pin 6 ( #pin 3 positive and #pin 6 negetive . may i correct)
and was this 0.22uf capacitor to connect IC 741
thanks
Manjunath, you can connect positive to pin6 and negative to pin3, but a non-polar would have worked better…I thought you would bring a ceramic disc type capacitor.
sir sorry to say that, i connected non-polar 0.22uf to the ic741 . but it was still not working perfectly even though i adujust 1k . which stage may be faulty as per your knowladge thank you very much sir
can't say exactly, your MIC could be faulty or assembled with wrong polarity or the IC may be faulty or with wrong connections…
when you clap the MIC grounds the pin2 of the IC momentarily which causes the pin3 and pin6 to go high, this the basic working principle of the circuit, you can confirm whether this is happening or not.
SIR I MADE THE SECOND CIRCUIT BUT SEEMS IT WAS NOT SENSING ACCURETLY. AS YOU SAID IT WAS NOT SENSING ABOUT 10 FEET DISTENCE .I SHOULD TOO NEAR TO THE MIC ,THAT ALSO NOT SENSING PROPERLY.
WAS THE FIRST CIRCUIT WAS MORE ACCURATE THAN THE SECOND PLEASE HELP ME
THANKS
Manjunath, you will need to adjust the 1K preset precisely for getting a proper response from the cirucit.
Initially, make sure the output of the IC just merely turns "low" (0V), by adjusting the 1K preset.
Thia will set-up the circuit optimally and claps from a little distance will also become responsive
this circuit is better than the first one.
Sir in second diagram where to connect VR1 as it contains 3 pins (the printed side facing us right side pin is negative, center pin is out, and right side is positive.) as per your diagram two pins are connected. Please help regarding this thank you.
Manjunath, VR1 here should be a preset not a pot, and by the way presets and pots do not have polarity, so the orientation is not critical.
you can use the center pin and any one of the outer pins, and leave the other pin free (unused)
hey what different thing can we use instead of led??
and use of relay is complusory??
LED is used for indicating the clap response, it cannot e replaced by anyuthing else.
the relay is for switching a load ON/OFF in response to the claps…
Hi swagatam ,I made a clap switch it's different from what you have posted here but works the same way. I want to Decrease it's sensitivity to make it a bit practical.
I was wondering if I could add a pot in series with the mic,will it help ?
Hi Shirish, yes you can put a pot or a preset in series with "R1" and adjust it appropriately for the required level of sensitivity.
I did and did not work the first circuit.
Can you give me an idea of what is not.
you can try the second opamp circuit or the one which is shown in the following article:
https://www.homemade-circuits.com/2012/04/simple-clap-switch-circuit-using-only.html
Dear sir,
I tried out the clap switch which turns on for two claps as suggested by you. But it is not working. Could you please tell me what's the problem?
Dear Anirudh, I'll try to update the article with a new easier one soon, you can try that once it's posted
why the collector in transistor is in the ground in the pcb layout?
It is a "component side view" layout
Sir, could you please tell me how to design a clap switch which turns on for 2 claps and turns off for one clap?
Anirudh, I have the circuit posted in the following article:
https://www.homemade-circuits.com/2013/04/clap-clap-switch-circuit-double-clap.html
but it will switch off also with two claps
Thanks a lot for your time and help sir.
If it's not a problem could you please tell me how to turn it off for a single clap?
Thank you again sir.
Anirudhs, the linked circuit is designed to work with two claps (ON/OFF), to make it operate with a single clap switch-OFF will require a complete change in the configuration and will make the design much complex….so it is not advisable to do so, moreover a single clap will make the design vulnerable to ambient noise.
Hello, I would like to use this circuit as a school project (toy car) using a 9v battery. How do I exactly do that and also, I already bought all the parts and a 9V motor and a 9V battery
Hi, you can try the IC 741 circuit, however it'll need to be tweaked appropriately for getting the most optimal results
Hey, iam from indonesian, i want to ask question, look over the PCB according to the first pat sensor circuit or the second ? ( clap simple switch that was given to me by one of the readers of this blog Mr. Dathan sharp . )
the PCB design is for the second circuit…
Hello Mr.Swagatam ……I have a minor problem…i made mr.ajay's circuit….but the problem is the sensitivity of the mic….the sensitivity of the mic is very low…it doesn't even responds from 0.5 feet…plzz tell how could i increase the range of mic to the extreme level….. i will be thankful for your quick reply…
hello harishwar, try a 10k preset in place of the shown 1K, and adjust it carefully to achieve the required sensitivity….hopefully this should solve the issue, other wise we may have to seek other options.
hello Mr. Swagatam Majumdar……
plzz sort out my problem as soon as possible…..
i made mr.ajay's circuit …it works perfectly but the main problem is the sensitivity of the mic….plzz tell how can i increase the range of mic to the extreme level…. i need the mic to work at least at the range of 5m….if its not possible…what is the maximum range of the mic….waht modifications should i do in the circuit…. plzz reply
you mean i should make the first schematic?
no, not the whole circuit, replicate only the diode section which are connected to pins 2,7,1,6,11 of the IC4017, make sure that now pin15 is connected to ground.
Just finised that but now not even the rel led doesen't turn on
connect one LED in series with R4 also and check its response, if this LEd lights up very brightly will ensure a proper functioning of the 741 section….then you can only replace the 4017 IC and recheck.
nope it doesen't work. i mean the relay doesent turn on. However i measure the voltage between the colector and the postivie voltage supply and it;s about 3V volt's.
it means your IC 4017 is not responding, may be it's faulty, put diodes at the output of the 4017 as shown in the first diagram and do the connections accordingly for the relay and the transistor also…..try it before discarding the IC.