In this post I will comprehensively discuss how to build a high power 1000 watt induction heater circuit using IGBTs which are considered to be the most versatile and powerful switching devices, even superior to mosfets.
Induction Heater Working Principle
The principle on which induction heating works is very simple to understand.
A magnetic field of high frequency is produced by the coil present in the induction heater and thus in turn eddy currents are induced over the metal (magnetic) object which is present in the middle of the coil and heats it.
In order to compensate the inductive nature of the coil, a resonance capacity is placed in parallel to the coil.
The resonant frequency is the frequency at which the resonance circuit (also known as coil-capacitor) needs to be driven.
The current flowing through the coil is always much larger than the excitation current. The IR2153 circuit is used to enable the working of the circuit as a “double half-bridge” along with the four controlled IGBT STGW30NC60W.
An equal amount of power is delivered by the double half-bridge as to the full bridge, but the gate driver in the case of the former is simpler.
IGBT STGW30NC60W
Using Anti-Parallel Diodes
The large sized double diodes STTH200L06TV1 (2x 120A) are used in the form of anti-parallel diodes. Even if the smaller diodes of 30A size will be enough for this.
In case you use the built-in diodes of IGBT such as STGW30NC60WD, then you will not be required to use the smaller diodes or large double diodes. A potentiometer is used in order to tune the operating frequency into resonance.
One of the best indicators of the resonance is the LED’s highest brightness. You can certainly build drivers which are more sophisticated depending on your requirement.
You can also use automatic tuning which is one of the best things to do, which is the course adopted in the professional heaters; but there is one drawback that the simplicity of the circuit will be lost in this process.
You can control the frequency which falls in the range of approximately 110 to 210 kHz. An adapter of little size which can be either transformer type or smps is used to provide 14-15V of auxiliary voltage which is required in the control circuit.
The Isolating Transformer
An isolating transformer and a matching Choke L1 are the electrical equipment which are used to connect the output to the working circuit.
Both these inductors are present in the air-core design.
On one hand where a choke consists of 4 turns on a 23cm diameter, the isolating transformer on the other hand consists of 12 turns on a 14 cm diameter and these turns are made up of double wired cable (as shown in the figure given below).
Even when the output power reaches to a scale of 1600W, you will find that there is still a lot of scope for improvement.
The work coil of the proposed IGBT induction heater is made up of a wire which is 3.3 mm in diameter.
Using Copper for the Coil
A copper wire is considered more suitable to make the work coil as it can be connected easily and effectively to the water cooling.
The coil consists of six turns along with the dimensions of 23 mm height and 24 mm diameter. The coil can get hot in case it is subjected to prolonged operation.
Resonance capacitor is made up of and consists 23 pieces of capacitors of small size which has a total capacity of 2u3. You can also use capacitors of 100nF in the designs such as Class X2 and 275V MKP polypropylene.
You can use them for this purpose even when they are basically not intended or made for such purposes.
The frequency of resonant is 160 kHz. EMI filter is always recommended to be used. A soft start can be used in order to replace the variac.
I would always strongly recommend you to use limiter which is connected in series with the mains such as halogen lamps and heaters of approximately 1 kW when it is being turned on for the first time.
Warning: the induction heating circuit being used is connected to the mains and contains voltage of high level and can be lethal.
In order to avoid any accident due to this you should use a potentiometer which has a plastic shaft. The electromagnetic fields of high frequency are always harmful and can have a damaging effect on the storage media and the electronic devices.
A significant level of electromagnetic interference is caused by the circuit and this in turn can also cause electric shock, fire, or burns.
Every task or process which you carry out is at your own risk and the responsibility will lie with you and I will not be responsible for any kind of harm which comes by in carrying out of this process.
Circuit Diagram
PCB Design
The following PCB design for the above IGBT induction heater circuit was provided by an avid reader of this blog Mr. Атанас.
220V AC to 220V DC Bridge Rectifier Circuit with Safety Lamp
The Choke L1
The design of the choke L1 used in the above full bridge IGBT induction heater circuit can be witnessed in the below given image:
You can make this by coiling 4 turns with 23cm diameter, using any thick single cored cable.
The following image shows the double coiled air cored isolation transformer design:
You can build this by coiling 12 turns with a 14 cm diameter, using any thick doubled wired cable.
The work coil may be build as per the following instruction
Please note that if the coil is tightly wound then only 5 turns may be required. If six turns are used then you may try stretching the coil slightly for achieving optimal resonance and efficiency.
UPDATE
Adding a Current Limit
The following diagram suggest how a simple current limiting feature can be added to the above explained induction heater design.
TIL111 opto-coupler Pinout Details
Here the resistor near L1 (let's call it Rx) becomes the current sensing resistor, which develops a small voltage across itself to the desired point when the current begins exceeding the safe limits.
This voltage across Rx is used for triggering the LED inside the attached opto-coupler. The output transistor inside the opto responds to the LED triggering and quickly conducts grounding the Ct, pin#3 of the main driver IC IR2153.
The IC shuts down immediately prohibiting any further rise in current. When this happens the current drops which in turn eliminates the voltage across Rx, thereby switching OFF the opto LED. This reverts the situation towards earlier normal situation, and the IC starts oscillating again. This cycle now repeats rapidly ensuring a constant current consumption for the load, within the predetermined safe limits.
Rx = 2/Current Limit
Feedback from one of the dedicated readers:
Dear Sir- I have successfully made induction heater 1/2 bridge with 4 IGBTs and i want to know that the 1000 watts heater lamp that's been suggested should be permanently connected to the circuit or only upto testing for the 1st time.
Images of the test result are enclosed here under:
Awaiting your reply at the earliest. Regards - Manish.
Solving the Circuit Query
Dear Manish,
While operating the induction heater do you see any glow on the series lamp?
If yes then probably it cannot be removed, if the lamp is in the non-illuminated state and completely "cold" (feel it by holding it) then it can be removed.
Regards
Feedback from Mr. Saeed Mahdavi
Dear Swagatam:
At last I was able to make my circuit work again after a lot of more attempts. And i shot the video with the bolt red hot.
I hope it could be useful for those interested in induction heaters. Would you please tell me how to increase the heat so that the bolt reaches melting point?
The voltage across the mains is 194 volts and the current consumed by the circuit is just 5 amperes and the wave form on the oscilloscope is quite sine waveform.
In my prototype I added a few turns to the RFC choke to get more voltage on the work coil and consume less amp.
The IGBTs worked quite normally without much heating during the operating period. Would you please tell me what I should do to get more and heat. Thanks a lot
Saeed Mahdavi
Video Clip:
With over 50,000 comments answered so far, this is the only electronics website dedicated to solving all your circuit-related problems. If you’re stuck on a circuit, please leave your question in the comment box, and I will try to solve it ASAP!
Hi
do i measure Current Limit or must this be calculated fo rx
Yes, Rx decides the current limit, you can calculate it according to the formula. But I think 2 must be replaced with 1.5, because the opto LED should light up when at least 1.5V is developed across Rx resistor.
Is it important how much amps the auxiliry voltage has?
Which auxiliary winding are you referring to in the diagram?
The 12 v to 15 v
Are you referring to L1?
Im referring to the input voltage that is needed for control circuit
Input voltage to the IC circuit can be between 12 to 15, there is no auxiliary winding in the above design.
If i wanted to turn this into a cooker would i just need to change the wire and its shape or would there be any other changes necesery?
Yes, you just need to modify the work coil to make it flat, by ensuring that the inductance value is not altered.
good I am an amateur I would like to develop this circuit but I feel that I lack more knowledge about measures you could send me to the mail this circuit with all its values and conetions please I want to undertake myself in this world of electronics and more with induction heating thanks.
Hello Eduardo, I appreciate your interest in this project and I understand that you want to build it, however, the above project is not an easy DIY project and requires prior expertise in the field of induction heaters, therefore this project is not for newcomers, because if you happen to get stuck somewhere, I may not be able to troubleshot it for you, without practically checking your circuit connections, so I would recommend you not to try this project unless you have gained sufficient experience in this field….
Can someone who has managed to run the circuit tell me what values the RX resistance is.And a trimmer for a drill can be used for a smooth start of the scheme that it exploded again
Hi, this circuit was tested by Mr. Saeed Mahdavi, but I do not have his email ID.
You must adjust the frequency using the 10k preset with the bulb connected until the bulb glow becomes minimal. This will prove that the circuit is resonating perfectly.
Merhaba,
ikinci şemada L1 bobin bağlantısında bir hata var sanırım. Devre akımı Rx direnci üzerinden geçirilmiş.
Hi, the L1, Rx connection in the second diagram is correct. The L1 is for suppressing voltage spikes, and Rx is for detecting over current.
I am sending a diagram with corrections, I tried it at 110 volts, so far it has not started, I will try it at 220 volts.
I replaced the transistors with more powerful ones, but I don’t know if they are compatible. SGH80N60UFTU IGBT Transistor 600V, 80A, 195W
The IGBT looks OK to me, and should work. Just make sure to add a series bulb initially with the input AC and optimize the IC frequency correctly.
joke, I replaced a 100 k ohm potentiometer and a 10 kilo ohm resistor, the frequency is from 18 khz to 160 khz. One circuit is activated but the other is not, the zener has no voltage
I managed to run the board with a laboratory power supply of 20 volts. There is an error when connecting to the integral, the two terminals must be exchanged. But after 2 minutes I burned the integral, that’s why I soldered the two boards with transformer ferrites 2 double 25 coils at the input and 25 for the output. You need to play a little which cable to connect where matters. 0.6 mm cable
OK, thanks for updating the information.
I forgot to mention on the integral that the power supply must be adjustable 9 to 15 volts.
OK, thanks, noted!
There is no point in dealing with the frequency, deal with the beats.
I replaced the burnt parts, made two integrated circuits, measured them with an oscilloscope. They gave 15 volts at the output, and I don’t know what this frequency is called, but there are small dashes above and below. With one circuit, the lamp lights up with the other one and goes out, but nothing happens. heats the meta.
Frequency is measured in Hertz. In the above circuit it should be in many kHz. You have to finely adjust the frequency by adjusting the 10k preset. If the frequency is not precisely adjusted then the circuit will fail to work.
Frequency is the most crucial aspect of the circuit.
Thank you very much for your help, if it wasn’t for you I would have stopped with the scheme. My smallest coil is 38 mm internal diameter 6 mm traba copper. The one I tested with is 62 mm. 6 turns. Should I use the smallest one?
No problem Atahac, I will try to help as much as possible.
All the inductors must be built exactly as given in the above article. If you change the specifications then something might go wrong.
The work coil must be 25mm in diameter with 6 turns of 3.3 mm copper wire.
Also, did you check the frequencies across the 1nF capacitor, pin7 and pin5, and by adjusting the 10k preset.
You should get a high frequency across these points and it must vary when the 10k preset is adjusted.
With 200 watts, I also test two separate circuits of the IR2153, with one the lamp lights up, with the second, one of my transistors burned out.
Is your IC oscillating and generating the required frequency for the IGBTs? The 10k preset must be correctly adjusted to match the correct frequency. Also the coil must be correctly wound and configured, if there’s any mistake in the coil configuration, it will lead to over-current situation on the IGBTs.
IR2104 MOSFET/ IGBT Isn’t this integral better, the one on the circuit two circuits I made and burned some things.
I don’t think a MOSFET would be required to drive the IGBTs, the IGBTs can be driven directly by the IR2153 IC.
This circuit is a difficult circuit so you might have some initial problems. Try using a 200 watt bulb instead of 1000 watt for the initial testing.
I changed some elements, this time it heats up the diode on the integrated circuit. I sent you a circuit board to your email, if it’s good you can post it here
I could not find any email from you, in which email ID did you send?
Is the circuit working for you now?
I got undelivered mail
Thank you very much Атанас,
I received the PCB design sent by you.
I have posted it in the above article, under the first schematic.
Hello, I took the picture, but I have a problem, the lamp lights up and the circuit does not start. I can suggest a circuit. I get 5 volts at the output of the integral 5 and 7
Hi, first you must confirm whether you IC is oscillating or not. You must confirm this with a frequency meter and by adjusting RC timing components of the IC. Also your coil winding must be correctly configured with correct polarity.
Can I make a furnace circuit with a capacity of 100 kw and melt aluminum weighing 100 kg?
Sorry, that may not be possible with the above mentioned circuit.
Hi sir, please let me know the value of shunt resister near the optocoupler, it was not mention in the diagram
Hi Kumar,
The formula for calculating the shunt resistor RX is provided in the article.
Dear sir, let me know can 30A diodes use for replacing STTH200L06TV1 this?
Hi Kumar, yes that will do, but it must be rated at 600 V and must be ultra fast.
Dear sir, please can you explain the type of 2.2uf/450v capacitors are electrolytic or mylar?
Hi Deshan, those capacitors can be metallized polyestor or polypropelene (PPC) type. They should be strictly non-polar.
i suggest to make a real isolation transformer. use a PQ5050 ferrite core. no gap is required. i calculate winding turns for 220vac input wind primary and secondary with 8 turns of 14ga litz wire. that will be overkill transformer . at 160kHz you should have more than 1500watts.
For 240vac input, make 9 turns and for 120vac input, make 5 turns
Hi denis Laporte,
Did you make this circuit if coupd you tell me if it works with your isolation transformer?
Is this avg( american ) or standardised gauge (SWG)?
i am sorry to tell about the insulation transformer is totally inappropriate and ineffective
Dear sir, please let me know how to find resonant capacitor value in this circuit?
Hi LGHD, sorry I do not have a formula for calculating this parameter.
Sir, then how you choice capacitor values in your circuit?
It is not my circuit, it was contributed by another author.
Hi we want to develop some induction circuit we pay you
Dear Mr Swatagam, I’m wish somehow to use this circuit or similar for hitting the flat CCA 60 square m . How to use induction Heather (with made high temp) for very lower temperature. Pls answer me you or some else. Yours coleg with many little resources from Makedonija
Dear Petre,
A high temperature induction heater can be used to generate low temperature if the input current supply is sufficiently reduced to suit the application.
Hi … I am a great fan of your site. My problem here in South Africa, cape town is finding simple parts like laminated transformer plates. If possible, please connect me with a company to procure transformer parts like magnet wire and plates to build the 9-0-9 centre tapped transformer.
regards
angelo
Thank you so much. Presently I do not have any such contacts, but I will try to find somebody. If I find one I will let you know.
Mr. Swagatam, if you can not test the action, give me your suggested command circuit and power. I will test the action.
I have some knowledge only about the following small circuits, my knowledge about high power full bridge induction heater is not good.:
https://www.homemade-circuits.com/simple-induction-heater-circuit-hot/
Excuse me, can you find me? Thank you
If there is a problem with the thyristor, thank you
I tested some circuits, but I did not get an answer, if you can help me
Actually, as you know high power induction heater circuits are complex circuits therefore it can be difficult for me to solve your problem without practically testing your circuit.
Yes, I know, but it can be a good experience for you and help me
I can understand your problem, but induction heater circuits are complex circuits we cannot judge the faults without a practical testing of the unit.
Hello Mr. Swagatam, thank you for your kindness. I really need this circuit. Please help me.
You are welcome Hossien, but I really do not have this circuit with me at this time.
Hello Mr. Swagatam, good morning. I want an all-bridge induction furnace circuit with a working frequency of 500 to 5000 Hz. Input 380 volts or 220 volts. Please help me. Thank you.
Thank you Hossein, I understand your requirement, however I do not have this circuit with me at this moment….if I happen to find it I will surely share it with you soon.
How to convert my OGBT welding machine to a heater induction up to 2000C
Sorry, no idea about it!
Пожалуйста поподробней о Rx шунта в обратной связи через TIL111.
Bir IGBT ile çalışan indiksiyon ocak şemasını siteden biri sağolsun yayınlamış, bunu size gönderebilirim.
Hello Swagatam Teacher, I’m sorry to bother you to benefit from your valuable information. I found the induction cooker schematic working with 1 IGBT Transistor, I even bought an induction cooker. It didn’t work for me in this stove. What I want to do is to make an induction heater. I run this stove I bought. When it reaches a certain temperature, the stove shuts down and when it shuts down, I have to wait by it all the time. If the IGBT Circuit works on its own by making abbreviations in this diagram, I can achieve my goal by connecting a relay to the heater’s heat meter. Since I do not have the ability to design a circuit, if I send you this schematic, can you help me make an IGBT Transistor-operated heater? Thank you so much.
Thank you Turan, However, I am sorry to say that modifying an existing induction heater can be extremely difficult, since induction heaters require a lot of calculations, and doing modifications can be quite risky. Furthermore induction heater is a difficult concept and requires a high degree of expertise in the calculations, which I unfortunately do not have at this moment.
Hello Swagatam, I benefit a lot from the information you have given, thank you very much. In the diagram you have given, these products are 4*IGBT STGW30NC60W, these products are expensive, I disassembled one induction cooker, 2200watt, this circuit works with 220v, only one H15 ME1 igbt is used in the circuit, I said let me make this circuit, but in the circuit ALP-01A C051X0008G1 integrated used, but I could not find this integrated anywhere from you. I need an induction cooker diagram like IHW 20N120R3 working with IGBT, I would appreciate if you could help me. Thank you so much.
Thank you Turan, I appreciate your interest, however I do not have the mentioned circuit diagram with me at this moment. If I happen to find one, will surely update it here for you.
Dear Swagatam, thank you very much for your interest. Thank you very much, I really benefit from your useful information, I hope you find the Induction cooker diagram that works with an IGBT transistor that I mentioned. Even if you can’t find it, best of luck. Thank you.
Thank you so much Turan, I appreciate your patience and understanding.
i am mecatronic engineer may languige farsi iran tehran low languig english your website very very good
Is there a reason this heater uses a control circuit to toggle the IGBTs instead of using a ZVS design?
It provides a wider optimization range for the user…
Thanks! I am not sure what “optimization range” is referring to here. Is it the range of LC values that you can use for the circuit, the range of frequencies that will work with a given LC value, or something else?
Yes, wider optimization for frequency, LC, current and voltage levels.
i am trying to build this on a PCB however i am having trouble finding away to integrate the anti parallel diode into the circuit board. is there something else i could use that will do the same job.
Diodes cannot be replaced by anything else. You must find a way to connect the diodes as mentioned in the diagrams.
Dear Sir
You have used 2.2UF x6 tank capacitors at the output.
Sir, Can I know how the value is calculated?
We are designing for three phase input, 5KW output load.
Can you kindly let me know…
Dear poornachandra, the capacitors are calculated as per its LC peak resonance frequency through practical testing and oscilloscope readings. The freqeuncy and the LC values are matched and tweaked until the output amplitude is maximum. You can refer to the following article for more info:
How to Design an Induction Heater Circuit
Dear sir, this induction heater uses 4x igbt, the power is quite large, my first question is, by adjusting the frequency to around 50khz and replacing the inductor with a calculated ETD59 transformer, this circuit is the same as 3kw smps, no feedback voltage is needed. oscillator is also simple ir2153. the second question is, igbt is replaced with a similar data FGH60N60 and many in the market. please advise and thank you for sharing your knowledge
Hello Widiatmono, your assumption is correct, but the modifications might requires a lot of calculations. Feedback is not give but that means the circuit is vulnerable to short circuits and overloads
Dear Swagatam
For the circuit shown (igbt induction heater)
Can I replace the 2u2 film capacitors with 1000u electrolytic capacitors for the half bridge converter.
Also what is the purpose of the RC network across the tank circuit(4n7 in series with 4R7) which is connected across the isolation transformer.
Thank you.
Dear Welensky, do you mean replacing with a single 1000uF/450V cap, no that won’t be appropriate. You will have to use many 2.2uF as shown in the diagram.
The RC network is for suppressing high frequency transients.
Dear mr. Swagatam,
How can I change from the air core isolation transformer to the ferriet core but the circuit does not change?
How can I cal them?
Dear nguyen, you will have to measure the inductance of the coils, and estimate their current handling capacity. once you have found them then you can build a ferrite based inductors with similar specifications.
Hello,
Above circuit limit current using negative shutdown signal.
how can i use TIL111 for current limiting ir2110 which is shutdown by positive signal.
Please give me circuit to shutdown ic using TIL111. IC requires positive shutdown signal.
Thanks
Hi dear sir i made this circuit and increased the power of this coil by using 3 separate circuits,Each of them is an example of your design. Of course, the IGBTs Trigger command is parallel, so there will no disruption to these three circuits And the outputs of the three circuits are connected through the circular ferrite that I did in the wiring star connection and tripled the work coil power and I could melt the steel and I wanted to share this experience with you Of course, I wrapped the copper tube 1.5 turns on the ferrite
best regards Sincerely yours
Thank you Sedigh, I appreciate your hard work and congratulate you on your success in upgrading the design to a much higher power output. Please keep up the good work!
Hello dear friend How do we find out that our resonance or tank frequency is created ?
Dear Friend, you can find the details in this article:
https://www.homemade-circuits.com/simple-induction-heater-circuit-hot/
Can i start with small voltages like 24v
will it work for this voltage?
yes it might work but the work coil might also need some change, are you new to this concept, then I won’t recommend this circuit
Can you describe the operating principle of the diagram?
The IC is a half bridge inverter IC which drives the IGBTs in the half bridge mode, and oscillates the respective coils at a high frequency as determined by the RC network at pin2/3 of the IC. The frequency finally oscillates the work coil at the resonant frequency executing the intended induction heating. Hope you got it.
thank you so much!1
How components like resistors or diodes and capacitors are calculated or chosen
Diodes are for allowing current to flow only in one direction, and for converting AC to DC. For resistors you can read the following articles:
https://www.homemade-circuits.com/use-resistors-design-circuits/
https://www.homemade-circuits.com/understanding-basic-electronics-how-to/
For capacitors you can read the following article:
https://www.homemade-circuits.com/understanding-capacitors-made-easy/
Hello,
I want to know that if I touch work coil will i get electric shock? What is the voltage inside work coil?
If i wont get electric shock please tell reason.
Waiting for your kind reply.
Thanks
yes you may get a shock, since it is electromagnetically linked with 220V mains.
Dear Swagatam:
I am really upset with my circuit. it has quite little heat,just as hot as making a wrench head red and not more. and when i boost the wattage of the lamp in series to get more heat, i lose two of my IGBTs (gw35hf60wd). i used these IGBTs , as i could not find the one mentioned in the schematic. on the other hand i am after melting iron and making it red. please help me what i should do so that my IGBTs remain safe on the hand and i can get as much heat as to melt iron on the other.
meanwhile, i was waiting to get to the heat and shoot a film, but …..could not yet
thanks a lot Saeed Mahdavi Asl
Dear Saeed, I am really sorry I do not have much idea regarding the design since it was created and tested by another person, according to whom the circuit worked perfectly. It is the frequency which actually affects the heat, so make sure it is best optimized perfectly while the load is placed in the coil
Dear Swagatam:
just a health concerning question,
as you have mentioned in your post, this circuit makes so powerful radiation. do you think it might be dangerous for its operator or it is quite safe??
have you ever researched about it??
thanks a lot
Saeed Mahdavi Asl
Saeed, as per my assumption the radiations may not be harmful to the user, because we have mobile towers at every corner of our cities and those radiations are much powerful than this, so if those are not a concern then this situation can be also ignored.
Dear Swagatam:
first of all, i thank you for all useful information you kindly gave me. concerning the induction heater with 4 IGBTs in your webpage , i should say I made it at last successfully. thanks God. it was all OK having little illumination in the 1200 watt lamp in series. while working, the coil got so hot and the bolt in it got quite red. however, i was intending to see the bolt melt, so i increased the wattage of the lamp to 1800 which caused one of my IGBTs to burn out after a few minutes.
1-Now would you please tell me if i have to keep the 1200 watt lamp in the circuit for good , which in this case i would have just a moderate heat not able to melt iron.
2- what else i should do to get to that heat?
3- if i could omit the isolater coil, which is contained of 12 turns of wire?
4- if i could change the 4 turn choke with an air cored one to a smaller one with feritte core?
thanks a lot
Saeed Mahdavi Asl
Dear Saeed,
I am glad you could make it successfully.
However since this was not designed by me,providing perfect solutions may not be possible for me.
I would recommend you to keep the circuit as it is, and add a current limiting stage as shown in the updated diagram above.
Once you configure the current limiting stage, you can try removing the 1200 watt series lamp and check what happens.
The current limit should be set with regards to the breakdown limit of the IGBTs and other relevant components.
Hello Dear..
First of all thanks for making such a nice & informative website 🙂
In the article above i found this line..
"In case you use the built-in diodes of IGBT such as STGW30NC60WD, then you will not be required to use the smaller diodes or large double diodes."
TO my understanding the above line means if i have IGBT with internal(built-in) diodes then i can change my circuit to
https://drive.google.com/file/d/0B3Pn7Yg7DiqkTURzRWxpdm5peE0/edit
means i can skip big antiparallel diodes?
Am i right?
Thanks Waqaar, I am glad you liked my site.
yes that's right, however I would not recommend removing the external protection diodes, after all the IGBTs are too important for the circuit and we would want to provide extreme protection for these device even if it costs little more to us.
Hi Swagatam, thanks for your posts, I used ones…are super. Please, is possible use this power circuit to Ultrasonic Langevin Piezo Transducer, change the final and with impedance coupling?
Carlos Benincasa
Thanks
Hi Carlos, I don't have mush idea regrading your device so it would be difficult for me to analyze the integration, however if you can provide more details regarding the specs and the operating principle of the device, I may try to suggest my views
Hi sir,can you provide a final circuit with component details of induction heater please sir
Hi Saketh, everything is furnished in the above article, please copy them on a notepad accordingly…
please try a smaller one first and then attempt this one
Hi swagatam…
I check output from ic ,pin5 & 7 disconnecting from gate IGBT,duty cycle is 30%…is it correct??
(data sheet ic duty cycle fix 50%)
Hi Aris, if the datasheet says 50% then it should be 50%
Please build it only if you are an expert with switching circuits, and high voltage circuits, otherwise not, because this design is not suitable for the newcomers.
tell me I made change IGBT STGW30NC60W