In this post I have explained a simple constant current bicycle dynamo battery charger circuit which can be used for charging a Li-Ion or Ni-Cd battery from a bicycle dynamo electricity source. The idea was requested by Mr. Saif Khan.
Technical Specifications
I want to charge a battery through a dynamo fitted to a cycle. Can you please tell me how to design the circuit for it. I don't know electronics. I will be really grateful.I don't know much but i live with electronic engg guys who know about it so if given a complete schematics they can do it. Can i order these online?
I am not sure a dynamo would be able to produce 28/30V. I have read that it can be limited to 4-20 V mostly
(I am using a simple motor..which will rotate and as well charge the battery). I know i am a total noob.
Just few points:
1. The input voltage, being connected to a dynamo fitted to a normal cycle will vary a lot but mostly be less than 20V, right?
2. The Li-Ion battery that will be charged needs to power an LED lamp for about 2 hrs. It has to be charged within 1-1.5 hr of cycling. That's pretty much my project.
1) The Design
The second circuit shown in the following link can be implemented for the above application:
https://www.homemade-circuits.com/how-to-build-simplest-variable-power.html
The dynamo input should be connected across the points referred 30V and ground, VIA a 1N4007 DIODE.
The 10K variable resistor which may be a pot or a preset should be adjusted to get the desired output voltage.
The LM317 should be mounted on a suitable heatsink.
The IC LM317 can work right from 3V to 35V inputs, so input variations won't affect the outcome.
The pictorial presentation of the proposed bicycle dynamo battery charger circuit is provided below.
It must be ensured that the pinouts of the IC are correctly connected as per the shown designations.
How to calculate current limit for this bicycle dynamo battery charger circuit
Rx is the current control resistor which must be selected as per the charging current specifications by using the following formula:
Rx = 0.6/charging current.
The next idea below explains how to simply charge Ni-Cd cells quickly using a dynamo device.
2) Charging 1.2 V Ni-Cd Cells (for Science Projects)
The second concept explains how to use a 6V dynamo for charging 3 Ni-Cd cells or Ni-Mh cells in series.
The design was requested by Mrs. Jennet through email, as given below:
"My daughter is in grade 10 and her science project is to charge a small battery using an exercise bike and a dynamo. Would you be able to assist in a schematic for this, as well as advise on what needs to be purchased in order for this to be built? Any assistance would be greatly appreciated. "
Materials Required
The materials required for this bicycle dynamo converter project are:
- 6V Dynamo = 1no
- 1.2V AAA Ni-Cd or Ni-Mh Cells = 3nos
- 4.5V Battery Box to Fix the above cells in series = 1no
- 10 Ohm, 2 watt resistor wire wound = 1no
- 1N4007 Diodes for making Bridge Rectifier = 4nos
- Any Cheap Small 100 mA Ammeter = 1no (optional, for indicating charging status)
The image of the battery box can be seen below:
Dynamo Specifications
The dynamo specifications can be studied from the following data:
It is basically a 6V dynamo, with a maximum current capacity of 500mA. Even at a slow bicycle speed of 5 km/hour, this type of dynamo will produce a decent output of 6V @ 100mA. This power could be used for charging an Ni-Cd or N-Mh cells or even a Li-Ion cell. Li-Ion cell might take a long time to charge at this rate, unless a buck converter is employed.
The cell specifications could be as indicated below:
How to Connect Dynamo with Battery
Connecting the dynamo with the battery and the rest of the mentioned parts can be implemented using the following wiring layout:
The connections look pretty simple. You will need a soldering iron and solder wire for joining the shown parameters.
Begin by making the bridge rectifier using 1N4007 diodes, as explained in this article.
Next, insert and fix the cells in the battery box.
After this, install the dynamo on the bicycle frame.
Finally, join the ends of the shown components using flexible wires with one another. Be sure to connect the ammeter with correct +/- polarity, otherwise the meter needle will deflect towards the left side instead of right side. (+) of the meter will go to the 10 ohm resistor.
Warning: Since the dynamo body acts like one of the output terminals, make sure it does not come in contact with any of the wire connections of the circuit, except the point where the lower orange wire is hooked up. In short, keep the diode side circuit secured inside a plastic box.
Testing the Charging Response
Once you have finished the procedures, start peddling the bicycle. You will start seeing some deflections on the ammeter. This will indicate that the battery is consuming power from the dynamo and is getting charged.
Now, as the bicycle is operated continuously, the battery will gradually get charged. This will be indicated by proportionately reduced deflection on the ammeter.
Until, finally no deflection or reading on the meter will be seen, which will indicate that the battery is now fully charged.
Bicycle Dynamo Battery Charger Circuit with Relay Changeover
By employing rechargeable batteries in the backup unit, the necessity for battery replacement is eradicated. The batteries remain on charge whenever the dynamo is in operation.
To minimize losses, no electronic devices are inserted into the source/lamps circuit.
In dynamo systems, the bicycle frame is typically utilized as the return current path by securely connecting one terminal of the dynamo to the frame.
Some commercial backup units demand isolating the dynamo from the frame, which is a challenging task.
The system described here, however, doesn't impose such a constraint, making it more accessible for both current and future dynamo users.
The output characteristics of all dynamos closely match the lamp load. In most setups, a 3W dynamo provides power to a 6V, 0.4A, 2.4W front bulb and a 6V, 0.1A, 0.6W rear bulb.
Regrettably, when the front bulb burns out, the rear bulb also fails shortly thereafter. When the rear bulb fails, the increased brightness of the front bulb significantly shortens its lifespan.
In fact, the authors once measured the open circuit voltage of a wheel-driven dynamo and recorded a peak-to-peak reading of 180V on the scope while pedaling in 10th gear!
Selecting the Right Battery
Regarding the battery choice, typical AA-sized NiCds boast a capacity of 500mAh and recommended charging currents of 50mA and 150mA for 15 and 4 hours, respectively.
When the bicycle is stationary, the total current supplied to both lamps by a battery composed of four NiCd cells is approximately 0.45A.
Consequently, a fully charged battery will last for approximately 45 minutes without dynamo assistance. It's important to note that under normal circumstances, the battery will not be utilized in this manner.
In situations where space is limited, the smaller 1/2A-sized NiCds offer the same capacity as the AA size but occupy only about half the space.
Additionally, non-rechargeable cells can be employed if necessary. In such cases, the charging circuit components D2, D3, R2, and C2 can be omitted.
If over-voltage protection is unnecessary, the zener diodes can also be excluded.
How the Circuit Works
The diagram presented above illustrates the entire circuit configuration for this unit. D1, C1, and R1 collectively supply DC power to the relay coil.
The point at which the bicycle's speed triggers the transition from battery to dynamo power supply for the lamps is determined by the component labeled B1.
For the particular Union model dynamo used, a speed of 20 feet per second yielded a smooth transition with minimal light flickering.
D2, D3, C2, and R2 constitute the charging unit.
Voltage regulation is accomplished through the back-to-back zener diodes ZD1 and ZD2. There are two operational modes:
a) Normal mode, with SW1 turned on: When the dynamo is stationary, the lamps draw power from the battery.
As the dynamo's voltage increases, the relay engages, and the lamps switch to dynamo power. The peak charging current in this mode is approximately 50mA.
b) Fast charge mode, with SW1 turned off: If the dynamo is engaged with SW1 turned off, the charging current increases to around 90mA.
This mode is useful for expediting battery charging while riding in daylight conditions. ZD1 and ZD2 play a critical role in limiting the voltage.
Without them, the charging current would surge to excessive levels, potentially causing damage to the NiCd cells.