In this article I have explained an alternator power booster circuit which was unveiled by one of the keen followers of this blog, Mr Michael Mbamobi. I have explained more about the details.
Technical Specifications
There is this circuit I want to show you. I want to show you the circuit through Homemade Circuit or Brighthub.
I didn't see how I can upload picture there. Please direct me I can sent this through Homemade Circuit. Anyway I uploaded the picture here! see the circuit and find out what these our Nigerian Guys are up to. I only hear about this type of device here in Nigeria.
I bought it and disassembled it. With your ability as Engr. Swagatam Majumdar, you can build a better device that can perform this same thing without depending on their own construction.
The folks call this an alternator power booster! It enables small gensets support loads bigger than their coils and feel alright with it without yearning!
I disassembled it carefully because D1, R1, R2, C2 and Q1 are obscured inside a glue like paste.
AC IN is from a small 650VA Generating set which is normally incapable of powering the connected loads.
The diode polarity and the value is not certain but this is its place in the circuit. It got broken while dismantling the glued circuit.
Q1 couldn't be traced either because the print was scraped of by the manufacture.Only its pin#1 and pin#3 responded to the DMM, it read zero like a dead diode, pin#2 does not read with any other pin at all. Pin#4 which is the tab is also unconnected.....just cannot figure out the device or its specs.
The diode D1 is blue in color, small glass type.
Solving the Circuit Request
Dear Michael,
It looks like an AC voltage booster circuit to me. Q1 is probably a power triac, the diode might be a diac DB-3, I am assuming this since it's small glass type and blue in color.
I would be addressing this circuit in my blog very soon....kindly stay tuned for the updates in my blog.
Thanks and Regards.
Circuit Explanation
The circuit appears to be a simple AC voltage booster. The main part which is responsible for supplying the excess power is the high voltage capacitor C1 which charges up with each AC cycle and reverts the power through the switching triac into the connected load.
The load thus gets added power due to the switching high voltage capacitor through the triac.
The triac is probably a BTA41/600A, which responds and switches ON as soon as the diac fires. The minimum voltage required for the diac to fire is around 30 volts.
The above concept can also be implemented with the following circuit which is simpler than the above and is also a lot cheaper.
The capacitor ratings may be modified and experimented with as per the load, and individual preferences.
However this circuit can be used only for heater applications such as irons, heaters, geysers, ovens, toasters, blowers, dryers, hot air gun etc.
Mains Voltage Booster using Two Capacitors and Two Diodes
Please use 1N5408 diodes instead of 1N5402, mistakenly shown in the above diagram.
Andries Henning says
Good day
I have a fivestar 1000w 12v to 22ov inverter but have some problems with it. The output is only 183v ac. how can I boost the output to give 220v ac.
I checked my 2 batteries and the DC is 13.5v.
Also can u please help me to increase this to a 2000w if possible. And a diagram to explain where to put extra mosfets.
Kind regards
Swagatam says
Please check the battery voltage after connecting a load to the inverter. The battery voltage might be dropping while a load is connected which may be causing the output to drop as well. If the battery is not dropping with a load and still the output is dropping then your inverter is malfunctioning, and will need to be checked and repaired.
To upgrade inverter power output you will need to replace its transformer, mosfets and the battery appropriately as detailed in the following article:
Calculate Battery, Transformer, MOSFET in Inverter
CHUKWUMA says
Please sir i want to ask you a question, 1N5408 DIODE and 1N4007 DIODE which one is higher, and which one is lower
Swagatam says
1N5408 can handle more current.
Chukwuma says
Please sir.can i use 1N4007 diode with 105/400v capacitor to build this booster
Swagatam says
you can use it.
CHUKWUMA says
Please sir if i use 1N4007 DIODE and 105/400V CAPACITOR can it give me high current or low current, and can i use it to iron my clothes on my i pass my nabbour generator
Adebanji Adewale says
Good day to you sir, I really love the way u respond to our questions here God will bless you, like I have came across this post b4 some years back, pls my question is, can this second cct be used to power pressing iron, heater when connected it to small 800va generator?
Swagatam says
Thank you Adebanji,
Yes you can use the diode/capacitor to power pressing iron, heater when connected to small 800va generator
Chukwuma says
Please sir,I want to ask you a question, The question goes like this, apart from CAPACITOR NUMBER 1N 105/400V and DIODE NUMBER 1N 5408, can i any other number of capacitor or diode to build this power booster.please sir I need your answer
Swagatam says
Hello Chukwuma, you can use other values for the capacitor, but lower values might give lower current output, and vice versa. However the voltage value must not be below 400V for a 220 V AC input supply
Nosa says
Hello honourable swatagam,how are u doing,I have an issues,1. how can i make 220vac transformer less to 10vac .
2. How can I converts or stepdown already 150vac to 10vac bcus d existing transformer in this one which suppose to stepdown 150vac to 9vac – 10vac and I could not get such transformer for replacement,very small transformer wit low ma, is now producing or giving out the same 150vac instead of 9vac – 150vac Tobe the correct output of powering a small logic board wit small lcd on it.
Swagatam says
Hello Nosa, if the output current requirement is lower than 50 mA then you can convert 150V AC to 10V AC using forward/reverse 10V zener diodes placed across the supply lines.
Nosa says
Thanks my honourable swatagam,I will check it out
Swagatam says
You are welcome Nosa!
Nosa says
Hello my honourable swatagam,you said 10v zener diode should be placed across the supply line’s. Do you mean the 10v zener diode should bridge the live and neutral connection or wires.
When you said forward/reverse,it therefore means that when output device is connected the 10v can flow from N wire terminal or L wire terminal,is that what you met by forward/reverse
Swagatam says
Hello Nosa, you can try the following configuration
https://www.homemade-circuits.com/wp-content/uploads/2022/01/10-V-AC-from-zeners.jpg
Nosa says
Thanks my honourable swatagam,your diagram is very simple,if i may get u,do you mean dat the main power supply input from 220vac to 240vac transformer less comes into your diagram and the output is 10vac.is that what the image explain or showing.
Swagatam says
Thank you Nosa, yes that’s correct a 240V AC at 50 mA current can be fed to the circuit for getting 10V AC.
Nosa says
Thanksy honourable man
Patrick says
Good morning Sir, please I design the same circuit but the output is reading 110v and if on load , no output at all. Please I need urgent solution
Swagatam says
Hi Patrick, How can that be possible, because the zener diodes are 10V rated? Try by connecting a small load, such as a 1K resistor
Nosa says
Thanks my honourable swatagam
Nosa says
Hello swagatem,happy new year and how are you be doing,my question is this, is it possible to pour in distiled water into deep circle battery for solar and charged it up,can d dead battery come back to life.
Swagatam says
Hello Nosa, Happy new year to you. Distilled water can be used. The battery may start working if the chemicals inside the battery are still in usable condition.
Nosa says
Thanks Mr swagatem maybe I should give it a try.
Nosa says
I have 12v 230ah deep circle solar battery totally drain out to 2v and I try charging it wit solar panel which it refuse to charge up and I design 12v charging system to charge it but d wires are very very hot during charging and burnt up,so what should I do because d battery voltage still remain 2v in it and it fails to increase to 12v upward.
Swagatam says
Connect a series 12V car headlamp bulb with the positive wire, and continue charging for many hours.
Nosa says
Thanks my honourable swagatam.
Nosa says
I have a question, concerning earth battery,how possible for it to power duplex and others.from what I saw on the Internet earth battery is usually 2v charged,so how do I get one bank as 12v 230ah or 400ah etc.how do I design or build such earth battery.pls give me links doing that
Swagatam says
Sorry I have no idea about it.
Nosa says
OK thanks my honourable swagatam. Love u big time.cheers
Swagatam says
It’s my pleasure Nosa!
Nosa says
My honourable swagatam,please tell me why you said I should connect 12v series of car head lamp bulb with the positive wiresults.
Swagatam says
Hello Nosa, as you said that the wires were getting very hot during charging, this could be due to very high current or a shorted battery. A bulb in series will ensure that the current to the battery is controlled, and the wires do not heat up. The bulb will remain illuminated initially and as the battery gets charged the illumination will slowly decrease until the battery is fully charged. If the bulb illumination does not decrease will mean your battery might be faulty. The bulb can be connected in series either with the positive line or the negative line….
Nosa says
Thanks my honourable swagatam, pls whats your recommended voltage to charge a 12v 200ah to 500ah battery or as from 40ah to 500ah 12v battery of deep acid lead circle battery or tubular acid lead battery.
Swagatam says
Hello Nosa, the voltage for charging a 12V lead acid battery is 14.3V but you can limit it to 14V for better safety. The current should be around 1/10th of the Ah value:
Lead Acid Battery Charger Circuits
Nosa says
Thanks my honourable swatagam,I was using 18v to charge 12v 200ah deep circle battery I told u about maybe dat was the reason the was very hot and getting burnt.
Swagatam says
Yes that may be exact reason why your wires are getting hot
Nosa says
Thanks my honourable swatagam, now my voltage is 18v can I use potimeter or variable resistor to reduce my voltage to 14v or 14.3v To try it back on 12v 230ah deep acid lead battery to charge it again or can I connect it to a 60ah pwm charge controller to charge 12v 230ah deep circle battery without reducing the voltage to 14v,can dis method work without having effect on the 60ah pwm charge controller.
Swagatam says
Thank you Nosa, you can connect the 18V with the following circuit and then adjust the pot to reduce the output to 14.2V:
Nosa says
Thanks my honourable man
Swagatam says
You are welcome Nosa!
Nosa says
Hello my honourable swatagam, can I join charge in paralle 12v 230ah deep circle battery that is drain to 0v to 2v with 12v 100th deep circle battery that is very good and fully charged to use it smart chargers Tobe able to charge the dead 12v 230ah deep circle battery.
Swagatam says
Hello Nosa, no, you cannot charge the deeply discharged battery with a charged battery, because then the charged battery will also get fully discharged, and neither will get charged.
You must use a 14V 25 amp charger to charge your 12V 230 Ah battery
Zafar Ahmed says
Hi Mr. Swagatam iam 62 years old man ritrired from Civil Aviation but iam ingage for life i see your all Electronic circuits and istady i liked your work
Best regard
zafar
Swagatam says
Thank you Mr. Zafar, I appreciate your interest and glad you liked my work.
Emmanuel obinna says
Sir thanks for your technical teaching, please I need a circuit that can help me boaster my generator current power so that it can withstand more loads without changing of sound pls
Swagatam says
Thank you Emmanuel, sorry, presently I do not have any circuit for boosting generator power output.
KonG says
Good morning and thank you for sharing your knowledge with us. I am searching for a circuit to step up 15v ac provided by my doorbell ring wires to 18-20v ac in order to use it with video doorbell. A solution is to change the transformer but I am wondering if there is other solution in order to avoid changing the transformer for 3-5 volts diferrence. The video doorbell needs about 300ma. Thanks in advance , waiting for your answer.
Swagatam says
Hello, the easy and better solution is to change the transformer, because making a boost converter can be rather complex, and might require some advanced knowledge in the field.
Lumen says
Please the 1 and 2 of the triac terminal, are they connect
Swagatam says
No, joints are shown in black dots
Jofrancis says
Hello Mr swagatam greetings, am impressed wt ur innovations more power to ur elbows. Plz I need voltage booster my generator alternator coil 230V goes down when I put loads esp small refrigerator of 50 litrs (freezer) wt other little appliances, so want to boost the voltage to 300V for easy carriage of the loads. I reside in Ikom Cross River State Nigeria, I’ll fund d cost of the boost, tell me the cost. My email jobnwobegu007@gmail.com. thanks in anticipation of your response
Swagatam says
Thank you jofrancis, the voltage could be going down due to heavy current drawn by the freezer, which cannot be corrected with a booster, instead you may have to upgrade the alternator power with increased current rating.
ghazal quadri says
please sir I really need your help on the write up based on the circuit requirements,design, explanation, analysis and circuit diagram on alternator power booster
Swagatam says
It is not possible to boost power of any source, output power will be always less than the input power
Umar says
I builds the second circuit with exact components but no outputs, and all the components are in good conditions.
Okcahi Johnson says
thank you Michael,plz i need this generator booster circuit diagram that can carry AC electric motor at least 1/2 or 1.0 HP, unlike the one that carries only boilers and heating elements . i love your works.Thanks and waiting.
gateman says
Mr. Micheal (Warbabylon) can help us with the complete circuit. Many of us are yet to get this circuit working. Thank you as you share.
Swagatam says
the last one has been tested by me, not quite sure about the first one…
Nebo says
Please can this second one power air condition?
Aljonguigue says
This is my email… Sir so pls…. Help me… Sir. Aljohnguigue@gmail.com
Aljonguigue says
Sir can u help me with my project in school….. I want to know on how to make a power booster…. With the help of you…..sir.. Example. When I have a 3000 watts generated power..I want it to boost into 6000watts or something higher than 3000 watts..
Swagatam says
Aljonguigue, that’s a technically impossible thing to achieve, you can never boost power. you can boost voltage or current, but the output net V x I will be always lower than input V x I
Saimtronics says
the circuit above with triac operates on the principle of controlling the firing angle of the triac
nnaemeka ekele says
Hello swagatam, am really glad meeting your post on this. Actually I've seen a generator booster that you can actually use with electric iron and heater. At the moment, am trying to reconstruct this circuit believing I will get my required result of a booster. I have all the components from the above diagram and am about to test it out. Please I have a 104/400v capacitor and a 3.5uf/400v capacitor mostly found in ceiling fans. I hope it will do the trick. Pls am really concerned about the booster circuit and I humbly ask you to throw more light on that. Thanks
Swagatam says
Thanks nnaemeka, a booster will work only if the input source has enough stock current, if it lacks current then the booster will fail to sustain the load.
you can use the mentioned fan capacitors for the second circuit…the shown design has been tested by me with a soldering iron and it worked perfectly making the iron red hot within minutes, and I had to switch OFF the supply to prevent the iron from burining.
Nebo says
OK please if you yes matter to read the voltage how many volts are you seeing?
nnaemeka ekele says
hello ive tried it using the fan capacitor and didnt get a feedback. please what should i do? Also, i saw a picture circuit where 13005 transistor was used with two 100k resistor, one 16k resistor and a ceramic capacitor probally a 1uf/400v. i coundnt get the actual circiut diagram. pls could you help me discover if the above components can be used effectively to boost electrical equipments like electric iron and heater. Thanks
Swagatam says
hello, I had used PPC capacitor in the second design, I could instant results from it, I am not sure why your capacitors didn't work?
The diagram at the top is the only one that i have, which was given to be by one of the readers.
Swagatam says
..I do not have much idea regarding the working of the first diagram as I am having difficulty in simulating it in my mind…so I can't help you with it…
ndukuba cyprain says
yeah,I like electronics , its most important and usefull thing in the world,but am still getting up in to it, i need an inverters way at an electronics ,I need help Swagatam
Swagatam says
Thanks Nukuba, if you have any specific questions, please feel free to ask…
Paul says
Hello once again sir Swagatam..
can i use this 2 non polar cap. 105J400V and 2 IN4007 instead of IN5408? its not available here.
Thanks Again..
Swagatam says
HiPaul, yes it will do…two parallel 1N4007 may not be required, you can use single 1N4007 diodes since the load in your case is small….
Sixtus Osinachi says
Dear Swag, thanks for your article. It’s very informative. Please is it’s possible to have a circuit diagram that can work with an Air conditioner. And secondly, what does Booster Capacitor do and how can one be designed.
Thanks.
Swagatam says
Sixtus, for an air conditioner you will need a transformer, a capacitive circuit might not work. The capacitor in the second circuit add their stored voltages in series to create a doubled voltage at the output
Paul says
hello sir Swagatam,
Our grid is 170 volts which is a low voltage and my soldering iron is rated 220 volts 40 watts?
can this be helpful to power up my soldering iron?
thanks again sir..
Swagatam says
yes the circuit will work for raising the 170V to 230V and more
Paul says
Hello Sir Swagatam..
Can i use this 2nd circuit for soldering iron that is connected to a low voltage grid?
Thanks in advance…
Swagatam says
Hi Paul, yes you can do it…
Ello Oku says
Can this work on solar powered inverter?
gabriel agyela says
Engr.Swagatam
I commend u for this wealth of knowledge you always made available to anyone who demand of it.my question is; can a variable resistor and additional capacitor be use to vary the amount of current that the load receive.In due course I will upload another circuit of the same function with the one mr Michael uploaded for your input and analysis. this is because this circuit has a variable resistor of 250K
Swagatam says
Thank you Gabriel,
Actually I am not sure about the first circuit since it was drawn by assuming the stages.
in the second circuit the current is controlled by the capacitor values….however this cannot be made variable.
If you have a more appropriate diagram you can surely send it to me for publication.
Swagatam says
Thank you very much!
A generator output is mainly dependent on the RPM of the alternator, which is governed by the correct timing of the CDI sparks….so may be the CDI sparks are not firing correctly in the ignition chamber of the generator…so perhaps this issue could be identified and rectified appropriately
Swagatam says
hello, thanks you…I had tried it successfully on a 25 watt soldering iron but yours is a 1000 watt press iron which might require a huge current….therefore the capacitors must be rated accordingly, may be upto 50uF to 100uF….but should be non polar type….you can try connecting many 105/400V capacitors in parallel for acquiring the results.
Olutayo Aboyade says
hello sir how was your day. my 1hp eletric pump affect my generator when ever i use it to pump water. is there any circuit solution for this to add to my 2.5kva generator to power it.
Swagatam says
hello olutayo, a 2kva generator should easily handle a 1hp motor, you must first check how much current the motor is trying to draw for the pumping operations, if it's more than 5 amps then probably you may have to replace the generator with a higher rated model.
Nwachukwu-Ejekpe Chibuzo says
Sir, still on this matter: if am able to buy one and send it to you will it help to solve this mistry and share the knowledge as you have been doing so kindly?
In all honesty your kind is very rare.
I want to say again that am highly impressed and humbled by your openess and willingness to share what you know and guide others like me without attaching a price.
People ask same questions and you patiently give answers and where you do not know you are humble to admit. Thank you, thank you and thank you again.
Am learning bit by bit, I loves electronics hopefully someday I will be good and able to help others too.
Finally, I did write you requesting for a circuit to help me charge my nicd drill batteries. You promised to look into it. Just a friendly reminder
Swagatam says
Thank you so much Nwachukwu, actually I have already published it in this site…you can check it out here:
https://www.homemade-circuits.com/2016/05/cordless-drill-battery-charger-circuit.html
chinaza onyenkwere says
Ok sir. Which circuit should I work on?
Secondly if it's the second one, does it require a transformer because transformer was mentioned in one of the comments yet I didn't see a transformer in the circuit. Please help me out.
Swagatam says
I have tested the second circuit with my soldering iron and it worked perfectly…so you can try the second circuit…transformer will not be required, just connect the source supply across the shown input wires, and the output wires can be connected with the load.
adding more capacitors in parallel will allow you to get more current for the load
chinaza onyenkwere says
From Onyenkwere Chinaza.
Please I use a 1000W pressing iron and I use a 650VA small generator. Does it mean that this circuit can help me use the iron with the generator?
If yes which circuit will work. The first or the second?
In the second is there a transformer involved?
Forgive me for the many questions, I'm a newbie in this field.
Swagatam says
No, the above circuits will not increase wattage or power, these circuits will only boost the voltage to double or triple values
Imuze Barnabas says
I have to agree with my fellow Nigerians that this thing WORKS… Its still kinda strange to me how the circuit could possibly make a 500W generator power a 1500W electric Iron, but somehow it works…perfectly in fact….for heating applications only though. Iron, cooker, electric kettle, .. It goes crazy on any other kind of load like a fridge…. I'd really like to know how this works… The mystery is eating me…
Eben says
Good day sir, I tried building the circuit using the two capacitors 105, 400v and the diode connected as shown in the circuit diagram but is wasn’t giving me an output voltage sir.
Swagatam says
Eben, It should give two times more voltage than the input, if the input is 240V , the output should be 500 V, please check the parts and connections properly.
onoriedode francis says
Hi michael…..good day,i'm Francis…..please could you share the circuit with me?!!!!!!!!?
Sos Sos says
Hi.
I want to view Posted circuit pictures. How do I view them because they don't seem to appear when I click on them?
Swagatam says
Hi, place the curser over the image, and click when it turns into a "hand" icon
emmanuel imafidon says
Hi Mr swagatam please can you device a circuit that can power fridge using
Triac diac and Micah capacitor please I need it urgently thanks Emmanuel Obayagbona
Swagatam says
Hi emmanuel, can you please specify what exactly are you trying to achieve…if it's getting more output than the input then I am sorry that's impossible and not feasible….
emmanuel imafidon says
But Mr swagatam,is there no alternative booster circuit Tha can power a fridge using tiger generator??
Swagatam says
can you specify the input power specifications and the fridge voltage and watt specifications, to be able to understand the situation.
yuzie says
Dear swagatam,
What rate (in VA) ur circuit above, and can it use for air conditioner 1hp inverter?
Swagatam says
Dear Yuzie,
the above circuits will work only with resistive loads not with inductive loads, and an inverter is an inductive load.
EKEH EMMANUEL CHIJIOKE says
as i posted earlier, i bought one of those power optimizer and i use a 650va generator set (called i pass my neighbour). this gen can not power up a 1500watt electric iron or heater but with the use of the optimizer/ power booster i was able to iron effectively and heat up my water several times and the first diagram looks exactly like d one i have. how i wish there is a way i an send u a snap shot of the components so u take a look at it yourself
Swagatam says
if you are able to generate 1500VA from a 650VA source by any method then that's a miracle and you must show it to the world, the idea can you a millionaire.
As for me I have no idea how to do it, as I told you before I am unable to simulate the first circuit so can't help with it.
a snap shot will not help because that will not reveal the circuit details or the component details of your circuit
EKEH EMMANUEL CHIJIOKE says
I BUILT THE SECOND CIRCUIT YOU GAVE SIR BUT IT DIDNT WORK. WHEN I PLUG IT TO LIGHT THE SOCKET COMES ON BUT WHEN I PLUG AN ELECTRIC IRON TO THE SOCKET, THE LIGHT GOES OFF BUT MY GEN REMAINS ON. PLS WOT EXACTLY COULD BE THE PROBLEM. I NEED UR HELP PLS
Swagatam says
I am not sure what you are trying do?
If you are thinking that this circuit will boost wattage then you may be wrong…the circuit will not boost wattage.
if your iron wattage is too big for the generator then no circuit in this world would be able to make it function.
the second circuit above will not boost voltage provided the wattage of the load is much smaller than the wattge of the fed input
Swagatam says
….sorry I meant
the second circuit above will only boost voltage provided the wattage of the load is much smaller than the wattage of the fed input
EKEH EMMANUEL CHIJIOKE says
am confused sir u said and i quote "The capacitor ratings may be modified and experimented with as per the load, and individual preferences". what exactly do u mean by this? is it that the 105/400v can be increased or reduced? if that is true what will be the effect of such increase or reduction? also if i have a 600va gen set and i want to use a 1500watt iron on it, will ur modified circuit work? if no what do u advice?
Swagatam says
yes you got it right, by increasing the uF of the capacitors in the second design you can increase the current or the wattage handling capacity of the circuit
but you cannot increase the output wattage than the input wattage by using any method, anywhere in this universe, that's not feasible.
EKEH EMMANUEL CHIJIOKE says
pls sir i bought one of those power optimizer as it were called and dismantled it and the circuit looks exactly like the first one uploaded and it was working fine but when i dismantled it, i discovered that the component numbers were wiped off, so my question is this, cant the first one work owing to the fact that it really worked when bought and secondly what is ur take sir. pls reply me and once again thanks for educating me alot
Swagatam says
Ekeh, if it was working before means it is a good design, but may be you broke something while trying to dismantle it, there must be something that was hidden and secret which you might have broke and that's why it isn't working now….
I am finding it difficult to simulate the first design so I can't suggest my opinion about it.
john ocharive says
thanks for your explanations on this booster. actually I have built the first circuit by mr Michael and I connected the positive to Q1 instead of negative and the device worked without any humming noise but when I reversed my connection to as it is in the drawing above I.e with negative to Q1 I discovered that the device was humming, and also I connected a metre to the output socket the output with out load was 50v but with load 100v. please can you explain these my discoveries.
more so, instead of a ceramic capacitor can't I use polarised ones because I have 4700uf 25v &1000uf 25v and I have IN5392MIC.
lastly can I use a diode instead of diac? thank you.
Swagatam says
to me the first circuit doesn't make any sense at all. C1 is connected directly across the power rail meaning it will only waste power and do nothing.
even if the circuit works it won't do anything significant.
the second circuit suggested by me has been tested by me and it really works, but only for resistive loads such as heaters
4700uF/25V will give you a big explosion.
Eno Igbe says
please what will happen when there is high or normal voltage conditions, won't it blow up the appliances?
Swagatam says
yes it will damage the load (resistive only) if the input voltage is restored back to normal.
Eno Igbe says
Mr. Swagatan, please what exactly is the booster used for or what is the purpose of the booster?
Swagatam says
Mr Eno, in the above shown circuits it's for boosting the performance of resistive appliances during low voltage conditions.
Swagatam says
It will take time…just keep investigating the circuits and the concepts theoretically and practically, when in trouble put up your question here to get them answered appropriately…in this way you will be able to gradually grasp the many aspects and get stronger in the field.
Swagatam says
it should be 105/400V not 104/400V. 104 = 0.1uF, 105 = 1uF so pls correct this in your circuit.
Stephen Emmanuel says
please mr swagatam how can i make the above circuiy yo power a refrigerator
Swagatam says
the above circuits will work only for heater types of resistive loads, not for other appliances.
Hyelda Yakubu says
Can i use it with microwave, connect to my 1.5 inverter
Swagatam says
It's not recommended, but you can give it a try, if there's no audible noise from the fan then it could be fine.
Lukeman says
Will ceiling fan capacitor work that is non polar capacitor? Pls help. Am waiting for ur reply sir.
Swagatam says
yes it will work.
Rahmon Tijani says
I think the triac use in mr micheal cct is BT151 but the diode I can't tell. Pls try complete the cct ƒσя ♏ε̲̣̣̣̥
Hyelda Yakubu says
Interesting but can I use it with my inverter 1.5 inverter
Swagatam says
It is recommended for resistive loads only.
Swagatam says
1N5401 is not a problem, and if you are using a soldering iron at the output even a 1N4007 will work as diodes.
check the capacitors, they might be faulty.
Swagatam says
It would be difficult to troubleshoot without seeing, actually my prototype worked very well, in fact the connected soldering iron became red hot within a minutes time and I had to switch power off to prevent the iron from blowing off.
Swagatam says
everything's already furnished in the above article.
prince Augustine says
Hello Mr. Swagatam. Please can this voltage booster be used for induction loads like centrifugal pumps, air conditioner, fridge, and motors?
Swagatam says
Hello Prince, A voltage booster based on transformers can be used with all types of equipment, but the above mentioned concepts are suited only for the resistive loads.
prince Augustine says
Mr Swagatam, I really appreciate your prompt response. Please do you have any such “transformer-based voltage booster ” circuit?
Best regards.
Swagatam says
Hello Prince, you can refer to the following article which shows how to connect the secondary of a transformer with its primary in order to create a voltage boost
https://www.homemade-circuits.com/how-to-build-2-stage-mains-power/
prince Augustine says
Mr Swagatam, appreciated.
Hyelda Yakubu says
Good day sir your article is really inspiring,pls can i use this circuit with my 1.5kv inverter to use my i.2kv microwave
Swagatam says
Thank you Hyelda, no you cannot use it for inverter, it is only recommended for resistive loads.