In this post I have explained how to make small homemade induction heater circuit for laboratories and shops for carrying out small scale heating jobs such as melting ornaments, or boiling small quantity of liquids using electricity or battery The idea was requested by Mr. Suni and Mr. naeem
- Circuit Objectives and Requirements
- Our challenge is to make an induction circuit for use from 12 V to 24 V with a flat spiral that can get half a liter of water to boil in as little time as possible.
- The primary goal is to get induction circuit to work but there are other challenges that are described below.
- The container in which the water should be boiling is of double-walled stainless steel and is insulated and the distance between the outer and the inner container where the induction works is about 5-7 mm.
- We have chosen induction in order to protect the electronic components from the heat of a conventional spiral heater coil which is possible when the tank is insulated.
- The outer container has a diameter of Ø 70 mm and the space for the electronic components is 20 mm high, so another challenge is to see if we have space for the components.
- In connection with the power supply there is connected a tilt switch which cuts the power to the induction loop in case the container is tilted 15 degrees or more. When the power to the induction circuit is interrupted this triggers an audio buzzer.
- Further, the induction loop is connected to two thermostats. One thermostat that interrupts power to the induction circuit when the water reaches boiling point and another thermostat that takes over to keep the temperature of the water at about 60 degrees - do not know if this will require a programmable circuit. I would also like to know if there are any infrared thermostats available.
- I know that this is a lot at once, but as mentioned, the primary aim is to get the induction circuit to work. Is it possible for you to send us a list of the necessary components and a diagram of the circuit.
- Looking forward to hear from you!
- Yours sincerely Súni Christiansen
- hello sir, i need a Induction Heater circuit diagram for our shop we have a silver jewelry shop
- so i want to silver melt and sometimes gold but if u send small circuit with transformerless power supply that will be good for me.
- I saw on internet very small project for induction heater but i cannot found power supply tansfomerless can you help me if u send both project Induction Heater and his power supply transformerless
The Design
In one of the earlier posts I have explained the basic method of designing a customized induction heater circuit by optimizing the resonance of the LC tank circuit, here we are going to apply the same concept and see how the proposed homemade induction heater circuit can be built for using in laboratories and jewellery shops.
The following figure show s standard induction heater design which can be customized as required by the user, as per their individual preferences.
Circuit Diagram
Circuit Operation
The entire circuit is configured around the popular full-bridge IC IRS2453 which indeed makes designing full bridge inverters extremely easy and foolproof. Here we use this IC for making a DC to DC induction heater inverter circuit.
As can be seen in the design the IC employs nothing more than 4 N-channel mosfets for implementing the full bridge inverter topology, additionally the IC involves an in-built oscillator and a bootstrapping network ensuring an extremely compact design for the inverter circuit.
The oscillator frequency can be adjusted by altering the Ct, and Rt components.
The mosfet H-bridge is loaded by the LC tank circuit using a bifilar coil which forms the induction work coil along with a few parallel capacitors.
The IC also incorporates a shutdown pinout which can be exploited for shutting down the IC and the entire circuit in case of catastrophic circumstances.
Here we have employed a current limiter network using BC547 transistor and configured it with the SD pin of the IC for ensuring a current controlled safe implementation of the circuit. With this arrangement in place, the user can freely experiment with the circuit without the fear of burning the power devices during the various optimization operations.
As discussed in one of the earlier articles, optimizing the resonance of the work coil becomes the key point for any induction heater circuit, and here too we make sure that the frequency is accurately tweaked in order to enable the most favorable resonance for our induction heater LC circuit.
It doesn't matter whether the work coil is in the shape of a spiral bifilar coil or a cylindrical coiled winding, as long as the resonance is correctly matched the result can be expected to be be optimal from the selected design.
How to Calculate the Resonance Frequency
The resonance frequency for the LC tank circuit can be calculated through the formula:
F = 1 / 2π x √LC Where F is the frequency, L is the inductance of the coil (with magnetic load inserted), and C is Capacitor connected parallel to the coil. Make sure to put the value of L in Henry and C in Farad. Alternatively you can also use this resonance calculator software for determining the values of the various parameters in the design.
The value of F can be selected arbitrarily, say for example we can assume it to be 50kHz, L can then be identified by measuring the inductance of the work coil, and finally the value of C can be found using the formula above, or the referred calculator software.
While measuring the inductance L make sure to keep the ferromagnetic load attached with the work coil, with the capacitors disconnected.
Selecting the Capacitor
Since a significant amount of current could be involved with the proposed induction heater for the lab works or for melting ornaments, the capacitor needs to be rated appropriately for the high current frequency.
To tackle this we may have to employ many numbers of capacitors in parallel, and make sure that the final value of the parallel combination is equal to the calculated value. For example if the calculated value is 0.1uF, and if you have decided to use 10 capacitors in parallel, then the value of each capacitor would need to be around 0.01uF, and so on.
Selecting the Current Limiter Resistor Rx
Rx can be simply calculated by using the formula:
Rx = 0.7/Max Current
Here, the max current refers to maximum current that may be permissible for the work coil or the load without damaging the mosfets and for optimal heating the load.
For example, if the optimal load heating current is determined to be 10 amps, then Rx could be calculated and dimensioned for restricting anything above this current, and the mosfets must be selected to handle in excess of 15 amps.
All these might require some experimentation, and Rx can be initially kept higher and then gradually lowered until the right efficiency is achieved.
Cooling the Work Coil.
The work coil can be built using a hollow brass tube, or a copper tube, and cooled by pumping tap water through it, or alternatively a cooling fan can be employed just below the coil for sucking out the heat from the coil from the reverse end of the enclosure. Other suitable methods can also be tried by the user.
Power Supply
The power supply unit required for the above explained induction heater for labs and shops can be built using a 20 amp, 12V transformer and by rectifying the output using a 30 amp bridge rectifier and a 10,000uF/35V capacitor.
Transformerless power supply can be unsuitable for an induction heater since that would require a 20 amp smps circuit which could be extremely costly.
Amjad Rafi Khagga says
suppose if I want to utilize your above circuit to make a DC to DC converter i.e. from 12 volt battery to 360 volts DC supply (to drive a small motor of 500 volts DC), would it be ok to use this circuit with an iron core transformer because I heard that it is ok to use iron core transformers if the frequency is less than or up to 10 khz or you may suggest some ferrite core one please guide me because I have least knowledge about transformer designing and calculations, in fact I only know the principal of the turns ratio and its relation to voltage and current transformation since power in is equal to power out minus losses, I also know that it requires less turns if frequency is higher, but I don’t know the relation between frequency and number of turns i.e. I don’t know the factors and formula to determine the core size and number of turns etc please guide me.
Swagatam says
You can use an iron core transformer, but then the frequency must not exceed 500 Hz, otherwise the iron core transformer might start getting hot.
For higher frequencies you can use a ferrite transformer.
Yes, as the frequency increases the transformer winding turns reduces.
However, calculating a ferrite transformer is not easy and might require a lot of calculations to be done.
Amjad Rafi Khagga says
instead of using IRS 2453 ic, can we use simple H bridge circuit made of complementary pairs of Bipolar Junction Transistors (A pair of NPN and PNP Transistors) such as 2n3055 and 2n2955.
Swagatam says
Yes, that’s possible, you can use any H-bridge, even PNP and NPN combination should work
Muktar says
How did I get Rt and cat calculation
BHUVANESH says
what are the specification values of induction heater using lc oscillator like frequency,power supply,capacitor value,inductor value ,and if any other specification values
Paul says
Hello,
Dear Swagatam.
Could you tell me if there is some type of circuit (as simple as possible) to handle a full wave bridge with regulation from 100 KHz to 1 Mhz. That is, to produce precise high-frequency alternating currents. I haven’t found anything on the internet.
Regards,
Paul.
Swagatam says
Hi Paul,
High frequency sine wave from the full-bridge transistor circuit looks quite difficult. I do not have this design with me at the moment. I will try to find it, if I find one will surely let you know.
Elias mohammed says
Distinguished Father of Knowledge
I want to be the best 50-1000 kg iron / steal melting induction furnance manufacturer in Ethiopia and in Africa as a whole
Dear Father, I hope you will help me make this dream a reality
I would like to thank you for providing this opportunity for discussion
From Ethiopia
Swagatam says
Hello Elias,
I appreciate your thoughts, however melting 50 to 1000 kg iron or steel might require a immensely huge induction heater circuit. Presently I do not have any information regarding how to design an induction heater of such proportions.
Fazal says
I need 3000 watts for getting 1000 centigrade.
Swagatam says
3000 watts is too high, I don’t have this circuit right now with me.
Omkar says
Dear Swagatam, I am electrical engineering student, trying to design 2000W induction cooktop. Please give me detailed idea to select components and design it using concept you explained.
Swagatam says
Hi Omkar, designing and calculating an induction heater can be difficult, therefore it is better to buy a smaller readymade unit and then upgrade it to higher wattage unit.
You can buy the unit which is explained in the following article and then upgrade it by replacing its coils and mosfets with higher rated ones.
2 Simple Induction Heater Circuits – Hot Plate Cookers
Omkar says
Thanks for replying
I alredy read this article you mentioned.
Where I can buy these units where same topology/technique is used. I will buy and study them.
Swagatam says
You can easily buy one of these induction heaters at reasonable rates from amazon or eBay.
Chinmoy MItra says
Dear Swagatam, I would like to point out that your statement “Transformerless power supply can be unsuitable for an induction heater since that would require a 20 amp SMPS circuit which could be extremely costly.” is incorrect. A 12V, 20 Amp conventional transformer is much more expensive than a 20 Amp SMPS. Nowadays these SMPS supplies are very easily available online as well as in the local market at very competitive rates. By the way, as usual your articles are very interesting. Keep up the good work.
Swagatam says
Thank you Chinmoy, I think you are correct, I agree with you!
Joel says
Hey Swagatam, I really like your circuit and understand most of it, but i cant find out the Purpose of the diode. Whats its Point?
Also, sadly the IRF540 isnt available anymore, so i just thought about using the IRFB7545. This should work, right?
Kind regards.
Swagatam says
Thank you Joel, the diodes across the gate resistors is to ensure quick discharge of the mosfet internal gate capacitance during off periods so that the mosfets can work efficiently.
Yes the mentioned mosfet can be used instead of IRF540
Joel Rupp says
Thank you for your answer Swagatam.
Im now thinking about the Rx, it has to handle quite high currents, so i guess the power it has to handle is also really high, isn’t it? Also im thinking about controlling the power by using a Potentiometer as Rx.
And, another question, sorry to bother you, I would use 48V as voltage for the coil, and regular 15V for powering the IC. This should work, right?
Swagatam says
You are welcome Joel.
Yes Rx wattage should be calculated as per the load current and this can be quite high.
First I would recommend using a fixed resistor for Rx, if it works you can think about using a variable one.
You can use 48V by isolating the mosfet drain line from the 15V line, and by using the 48V across the drain line of the mosfets. Just make sure the grounds of both the supplies are connected in common with each other.
Joel Rupp says
Hey Swagatam.
I was wondering about how to controll the current flowing in the coil. Because im not really seeing anything resisting the current from just being really high.
Now i’ve settled with just using rectified mains voltage (about 200V when rectified) for the Induction coil, so i cant really have more than 16A flowing in the circuit. I would prefer to have about 10A to get about 2000W in the End.
Thank you in advance,
Joel
Swagatam says
Hi Joel, the current can be controlled by setting up RX appropriately. However, this design is only on a concept basis and might require a lot of improvements. I checked online for a full bridge induction heater, and I realized that a link coil and a resonant series capacitor is recommended for a full bridge induction heater. The link coil and the capacitor can be adjusted to set the maximum current through the coil.
Here’s the reference article:
https://www.researchgate.net/figure/Full-bridge-inverter-fitted-induction-heating-equipment_fig1_275406215
http://www.richieburnett.co.uk/indheat.html
j k barik says
Hello Swagat ; what I say is that instead of using 15v for powering coil through mosfets , if we use 150V by using DC-DC booster ckt , will it help? I think it will draw less current for same power. 15V – 300w will draw 20A. But 150V – 300w will draw only 2A. Hence coil diameter will reduce so much. will it help? How we have chosen 15V for supply.
thanks
Swagatam says
Hello JK,
yes the mosfets can be separately fed with 150V DC, and the work coil calculated to match the 150V parameters. This will help to reduce the current to the coil and keep it much cooler. But the size of the coil may increase, because the number of turns depends on the voltage.
John Gile says
Dear Swagatam,
I have come several times to your site looking for a 60Hz 120v induction heater. I am VERY clumsy with electronics, it just doesn’t sink in. I would like to make a coil about 1″ inside diameter and just use house current to power it. I am not looking for instant red-hot metal heating, just more of a low grade heater. I see some companies making this type of induction heater but they are very expensive. I understand that the higher frequencies are very efficient. I’ve tried to figure out the wire/coil size for that frequency but I just don’t understand enough to do it. I would make sure the coil would not be touched to get shocked. Any help would be very appreciated.
John
Swagatam says
Dear John, you can try the first circuit from the following article, or simply purchase the kit from amazon which can save you from unnecessary constructional hassles:
https://www.homemade-circuits.com/simple-induction-heater-circuit-hot/
Or if you want a low tech design, then you can try working with the following concept:
https://www.homemade-circuits.com/small-induction-heater-circuit-for/
Amjad Rafi Khagga says
Dear John Gile use a solid cylindrical threaded (triangular threads) block of pure iron (soft iron and not even MS (mild steel)) having dimensions of 6 inch dia and 6 inch height, hence wrap an enameled wire of copper within threads and thickness of wire should be according to the pitch of threads for instance a wire with the thickness of 3mm then after completing this task you can apply directly (without using any electronic circuit) 110 volt AC 60 HZ.
Swagatam says
That sounds dangerous to me.
Omer Reza says
Hi. Is the 33 resistor 33k or just 33 ohm ? and can I use a 15v battery instead of the power supply ? Lastly For inductor coil, if I use just single winding of coil, is there any modification needed in the circuit? (does it depend on no. of winding of coil)? Thanks in advance.
Swagatam says
When only number is given for a resistor, then it is always in just Ohms.
This circuit is not easy and not recommended for newcomers…the circuit will require proper adjustment of frequency and RC resonance, and coil inductance.
Siamak says
Good morning Swagatam,
I have this wireless night light that has stopped working and when I opened it up I saw a burnt resistor I have no Idea how these things work would you be able to help please.
Swagatam says
Hello Siamak, can you upload the image on any free image hosting site online and provide the link here? I will check the image link and try to understand the fault!
David Kolář says
Hi Swagatam, first of all I want to thank you for your quick response. I appreciate it so much!
But there is still a second question that lies with my heart. Are there any options on the market to have the whole circuit designed? I would need to be able to control the entire circuit with an on/off controller created by LabView for instance. Which companies would you recommend to me?
Again, thank you very much for your time, it means a lot to me.
Swagatam says
You are welcome David, there are actually plenty of induction heater kits available in the online market that you can buy, here’s one example posted in this link:
https://www.homemade-circuits.com/simple-induction-heater-circuit-hot/
After this, you only have to measure the inductance of the work coil, and then replace it with your version having exactly the same inductance.
David Kolář says
Hi Swagatam, I would like to ask you, if it is possible to assembly this circuit on the white breadboard. Are there some limitations/restrictions for the white breaboard in term of coil power?
Thank you very much in advance.
Swagatam says
Hi David, breadboard assembly can lead to loose connections and cause problems in critical circuits like the above therefore it s not recommended, so assembly by soldering is recommended for such designs. Coil connection is absolutely not recommended in breadboard due to low current handling capacity of the breadboard
Narasimha K L says
Namaskar.
Can you please give me an assembled inducution heating circuit that can work on 12V or 24V battery supply.
Swagatam says
Hello, you can easily buy it online from amazon
Siamak MOTADI says
Hi Swagatam, I am working on Pellet 3D printing, and 12v/24v DC Induction Coil Heating is very attractive and interesting, my project requires Max of 350° C heat but the temperature varies in different locations on a Steel, Aluminium, or Copper pipes, (have not decided which material to use yet) my question is how to control the temperature using either Thermocouple type K (I got one that’s why I mentioned it) or Thermistors (got some them too) as sensors, would you be able to help me please, just the controller part, the rest is easy to get hold of on Internet.
Many thanks in advance, and my E-mail is : siafix@free.fr
Many thanks again.
Siamak
Swagatam says
Hi Siamak, I think a thermocouple based design will be good for your requirement. You can try the last circuit explained in the following datasheet:
https://www.analog.com/media/en/technical-documentation/data-sheets/ad8494_8495_8496_8497.pdf
The output will need to be configured with a comparator so that a relay driver stage could be toggled for switching the induction heater ON/OFf.
Siamak says
Good afternoon Swagatam,
Thansk for your prompt answer, I really appreciate your input, I will certainly look into that and see what I can understand from it sicne I am not at all in electronics, I am retired mechanical engineer so …
Cheers and many thanks again.
Siamak
Siamak says
Hi Again Swagatam,
What is really controlling the temperature in the induction heater coil, is it the Frequency or the input voltage, I really not in it all, I need may be a little tutorials to understand the whole thing the Induction Heater coil I understand how it works, well roughly, but how to control the temperature of the tube inside the coil is a mastery to me.
Thanks again.
Siamak
Swagatam says
Hi siamak, the temperature can be controlled by controlling the supply current. So if you use a power supply with a variable current facility, you can use it for adjusting the induction heater output as desired. Voltage variation can be also be tried for controlling the output temperature.
A basic induction heater concept is explained in the below article, which uses the ZVS technology which is supposed to be the most efficient.
2 Simple Induction Heater Circuits – Hot Plate Cookers
Siamak says
Thansk you very, very much now I understand a bit better, the rest is calibrating the Thermocouple to get right temperature, great.
Thanks again, you are a STAR.
Siamak
Swagatam says
You are most welcome, keep up the good work
Siamak says
Hi Swagatam,
I have just been looking at one of your power supply tutorials and I must say it is really easy to follow, for a non electronic guy I almost understood it and will follow the instructions to try to build one, you don’t have the circuit board lying around by any chance? I will be more than happy to buy it from you, the one with the Transistor 2N3055 that has adjustable Voltage and Current.
Many, many thanks again.
Cheers
Siamak
Swagatam says
Thank you Siamak, I undersatnd your concern, however I do not sell assembled items through this website, so I won’t be able to help you with your request, although i truly wish I could.
Siamak says
Hi Swagatam,
No Problem, I understand, is there any other site that you would recommend please.
Cheers
Siamak
Swagatam says
Hi Siamak, I do not know about any other site, but you can probably search for ready-made DC power supply modules from amazon eBay etc.
Siamak says
Thank you Swagatam, I really appreciate your input and as soon as my prototype is ready will give you a buzz.
Cheers and thanks again.
Siamak
Swagatam says
No Problem Siamak, wish you all the best, please keep up the good work!
Siamak says
Hi Swagatam, I have got hold of many items in order to fulfill the project I have in mind, one of them is induction cooker, my question is; would it possible to change the coil on induction cooker in order to make it a high temperature furnace or a Kiln to fire Ceramics and a like, (1200° C or 2192 F ) if yes how please, I was thinking using copper pipe to make water flow through it in order to cool the coil, but no idea how many turns, but I know the diameter, 90mm, so would you please guide me in this?
Many thanks in advance.
Siamak
Swagatam says
Hi Siamak, making a induction heater can be quite difficult unless you know all the practical details. So it is better to buy a ready made unit which may be quite cheap nowadays. After buying you can check the details, and then may be replicate it for future applications.
Even I do not ahve the necessary details regarding the coil diameters for a kiln application
Siamak says
Hi Swagatam,
Many thanks for you honest reply, really appreciate it.
I will follow your advise and get a 2500W one to see how that may pan out for me.
Cheers
Siamak
Swagatam says
You are welcome Siamak!
Siamak says
Good evening Swagatam,
I am so sorry to bother you again, but as you know I have knowledge of electrical things at all, so here it goes; I would like to heat the 3D printer bed to 140° C the actual one reaches 110°C, I would use heating elements to do so, what I am asking is would you please let me know the length and the wire size to get this wright for the 3D bed size of 500mm by 500mm, of Aluminium and glass.
I would be really more than happy and appreciative if you would please help.
Many thanks
Siamak
Swagatam says
Thanks Siamak, Designing the coil dimension of an induction heater might involve many critical calculations by considering many different parameters, which may be actually not easy and might require plenty of time and practical verifications. That is the reason it is better to buy a readymade unit and then try modifying it accordingly…or may be simply use an ordinary resistive heater coil for the heating purpose by controlling its heat with a light dimmer, which can be also quite efficient.
Siamak says
Good morning Swagatam,
Sorry for miss leading you, I meant resistive heating elements, I don’t know how to calculate it at all, I would like you to help me to make the it.
If you would please from the information i.e. the temperature, and surface to heat up.
I would like to heat an Aliminium plate (The Printing Bed) 3mm thick and on top there would be a glass plate of 3mm thick too, and 500mm by 500mm area to get to the temperature of 140°C max, I don’t have any preference on the power supply, it could either be 24V or 240V, so would you be able to help me please?
Many thanks
Siamak
Swagatam says
Hello Siamak, for resistive heating you can use a light dimmer circuit for controlling the heat to any desired level, as per your working specs.
For setting the temperature you will need a accurate thermometer.
The circuit of light dimmer can be studied in the following artciles:
How Triac Phase Control Works
Simple Light Dimmer and Ceiling fan Regulator Switch
Siamak says
Good morning Swagatam,
Thank you very much,
That is not what I wanted, I have PID to control the temperature, what I would like is to calculate how much resistive wire I need, i.e the gauge, the length etc. to reach the temperature of 140°C for a surface of 500mm by 500mm, I don’ know how to calculate this at all, I am not an electrical engineer just mechanical one and retired too so I have lost all I have learned at Uni, would you be able to help me please?
Many thanks.
Swagatam says
Siamak, I do not have the calculation details with me either. If you only need an accurate practical result then that can achieved through experimentation, but if you are looking for formulas then sorry I do not have it with me right now…I may have to investigate it.
Siamak says
Good morning Swagatam,
I have given up making one, it is too complicated and the results may not be what I want, so I am going to buy ready-made one form e-bay or Amazon, much easier and more reliable.
Many, many thanks for trying anyway, I appreciate it.
Cheers
Siamak
Swagatam says
No problem Siamak., yes it is better to buy and research a ready made unit instead of risking failures and investments…
Fabinho says
Hi swagatam, is there a way to measure or estimate the power of the heater, only by looking at the values of its components (voltage, inductance, etc)?
Swagatam says
Hi Fabinho, you can estimate by looking at the coil element thickness, and the power rating of the mosfets, these two elements can provide a rough idea regarding the power output of the heater.
fabito says
Hmmm, and how exactly is that? Because for me we should pick a mosfet according to the desired power, right?
Swagatam says
Yes that’s right! The ID and VDS of the mosfet should be more than the expected power wattage output.
fabitinho says
Thanks already for answering me. So how can I know the expected power output to pick the right mosfet? Here you say: “the max current refers to maximum current that may be permissible for the work coil or the load without damaging the mosfets and for optimal heating the load” is there a way to relate this maximum current to the power? Or I simply look for a mosfet that handles this current and see its power specification?
Swagatam says
From the datasheet of the MOSFET, check the ID (drain current) and VDS (drain-to-source voltage) quantities, and multiply them together to get the maximum tolerable wattage of the device, provided it is mounted over a recommended heatsink. These must match your circuit’s V and I levels.
fabio says
Ok, so just to make it clear, if i’m switching the coil over a 15 DC voltage source, and I limit the current to say 20 amps, I should expect a power output of around 300 W? I should then pick mosfets that handle these voltage and current specifications. The switching frequency does not influence (much) in the power output?
Swagatam says
Yes, the mosfet VDS could be around 30V and current ID at 30 amps for the mentioned specs. MOSFETs are normally rated with high switching frequencies so that won’t be a problem.
Fábio says
Ok, thanks for the attention!
hosein simorgh says
dear.swag/i am iranian and very not domenstrate to english but know fully translate to persian and very tank you for share your train i love you
Swagatam says
Thank you dear Hosein, please feel free to ask anything related to electronics through translation… I’ll be most happy to help!
fmfm58 says
Merhaba bayım
İndüksiyon ısıtıcı devresi nasıl tasarlanır sunumunda R1 ve Ct nin değerleri ne olmalıdır.
Teşekkür ederim Saygılar
Swagatam says
Merhaba Fm, bunu henüz yapmadım, bu yüzden tam değerleri bilmiyorum. Parça değerlerinin verilen formül ve bazı deneme yanılma yoluyla hesaplanması gerekecektir.
Dinesh Kumar Panchal says
Welcome
Swagatam says
Dear Saeed,
I am so glad you could ultimately succeed with it.
I will try to give you a perfect solution, and help you to eliminate the bulb in seres
but for this you will have to do a couple of favors to me. 1) Please post this answer under the exact article which you have accomplished. 2) Provide a video clip of your experiment and send it to my email, so that I can use it in my article and share your success story with the world.
I hope you will not mind doing the two things 🙂
Saeed Mahdavi Asl says
Dear Swagatam:
here i should say the page in which you have introduced the induction heater with 4 IGBTs( https://www.homemade-circuits.com/induction-heater-circuit-using-igbt/) will not give me the link(Reply) under which i could post you my questions. but this page does prepare us the link. please fix it so that we could contact with you through the same page. and concerning your second request, OK I will certainly and happily do it by shooting a short film and posting it to you as soon as possible.
thanks a lot for all your kind helps
Saeed Mahdavi
Swagatam says
Dear Saeed, I am sorry I was not aware that the comment box was accidentally closed in the IGBT article, I have enabled it now, please post it now, this will allow the visitors to know about your successful experiment.
And I will surely wait for your short video clip which I can post in the same article for the benefit of the readers.
zaphira says
I am working on a project which needs me to switch off the safety mechanism, which shows an error every time the utensil is lifted from the top. I would like to know what mechanism is used to apply this feature in commercially bought heaters and is there anyway around it.Looking forward to your reply. Thank you.
Swagatam says
you can do it by enclosing small magnet and a reed switch in such a way that the magnet lies over the reed relay and keeps the reed always activated.
but the moment the ferrous utensil is placed, the magnet moves upwards towards the utensil and sticks to the roof of its enclosure…this moves the magnet away from the reed relay enabling it to get deactivated.
the reed relay can be appropriately configured for the intended cut off.
oyeledun bukola says
sir i need you to send me your email. i want to send you a circuit diagram for elaborate explanation
oyeledun bukola says
sir do you have article on inverter welding machine and if yes pls i have two welding machines 'schwarze 1080 model' they both power on but are not welding pls sir how do i troubleshoot them?
Swagatam says
you can try any square wave inverter circuit rated at a wattage higher than your welding machine wattage.
oyeledun bukola says
sir how do i come about the Rx Ct and Rt. pls help me sir
Swagatam says
please go through the article and the various links
the Rt/Ct is provided in the following article:
https://www.homemade-circuits.com/2014/01/simplest-full-bridge-inverter-circuit.html
Rx formula is also given in the article.
oyeledun bukola says
thank you sir. but can you shed more light on ct, Rt and Rx
oyeledun bukola says
pls sir can you assist me on how to download proteus software online
Swagatam says
oyeledun, I normally do not use on artificial softwares, instead I rely on my brain simulation and practical verification for creating new designs….therefore I am sorry I won't be able to help you much with software simulation
Swagatam says
you can download it from here
http://www.mediafire.com/file/xjxpbze64htdeac/Proteus+v8.1+SP1+Pro.rar
oyeledun bukola says
pls sir can you explain the main parameter responsible for an efficient induction in the resonance level of the LC circuit and how do i adopt it with the concept above? thank you sir.
Swagatam says
It's already explained thoroughly in the above article and in the hyperlinked articles, please go through them carefully…
oyeledun bukola says
sir i am happy to bump into this wonderful site. my name is segun jokojeje i work at olatundeprestige limited. at my working place, we deal with furniture, i mean we manufacture chairs using furniture. now i am been employed as researcher. i am being told to research on "HOW TO BUILD HIGH FREQUENCY HEAT GENERATOR OF ABOUT 20KW USING THE PRINCIPLE OF INDUCTION COIL" pls sir i need your assistance
Swagatam says
Thanks Joko, You are most welcome!
You can apply the concept which is explained above for your application also, the main parameter responsible for an efficient induction is the resonance level of the LC circuit, which must be correctly optimized.
Please feel free to comment here if you have any further doubts.