The following 5 versions of 6 volt 4 AH battery charger circuits has been designed by me and posted here in response to the request from Mr. Raja, I have explained the whole conversation.
Technical Specifications
"Dear sir, please post a circuit to charge 6 volt 3.5 ah lead acid battery from 12 volt battery. The charger should automatically stop charging as the battery is fully charged.
Please use transistor instead of relay to stop charging, and also tell me how to use 12 volt relay for the same circuit.
Explain Which is safe and durable either relay or transistor to cut off charging. (At present i am charging my above said battery by simply using LM317 with 220 ohm and 1 kilo ohm resistors and a couple of capacitor) i'm awaiting your article, thank you".
The Design
The following circuit shows a simple automatic 6 volt 4 to 10 AH battery charger circuit using a 12 volt relay, designed to automatically cut off the supply to the battery as soon as the full charge level for the battery is reached.
How it Works
Assuming no battery is connected with the circuit, when power is switched ON, the relay contact will be at the N/C and no power will be able to reach the IC 741 circuit.
Now when battery is connected, the supply from the battery will actuate the circuit, and assuming the battery to be in a discharged state, pin#2 will be lower than pin#3 causing a high at pin#6 of the IC. This will switch ON the transistor relay driver, which in turn will shift the relay contact from N/C to N/O connecting the charging supply with the battery.
The battery will now begin charging slowly and as soon a its terminals reaches at 7V, pin#2 will tend to become higher than pin#3, causing pin#6 of the IC to become low, switching OFF the relay and cutting off supply to the battery.
The existing low at pin#6 will also cause pin#3 to become permanently low through the linked 1N4148 diode, and thus the system will be latched, until power is switched OFF and ON again.
If you don't wish to have this latching arrangement, you can very well eliminate the 1N4148 feedback diode.
Note: The LED indicator section for all 3 following diagrams were recently modified after a practical testing and confirmation
Circuit#1
The following circuit shows a simple automatic 6 volt 4 AH battery charger circuit without using a relay, rather directly through a transistor, you can replace the BJT with a mosfet also to enable high Ah level charging also.
PCB Design for the Above Circuit
The PCB layout design were contributed by one of the avid followers of this website, Mr. Jack009
Circuit#2
Update:
The above transistorized 6V charger circuit has a mistake. At the full-charge level as soon as the battery negative is cut-off by the TIP122, this negative from the battery is also cut-off for the IC 741 circuit.
This implies that now the IC 741 is unable to monitor the discharging process of the battery, and will be unable to restore the battery charging when the battery reaches the lower discharge threshold?
To correct this we need to make sure that at the full-charge level, the battery negative is only cut-off from the supply line, and not from the IC 741 circuit line.
The following circuit corrects this flaw and makes sure that the IC741 is able to monitor and keep track of the battery health continuously under all circumstances.
How to Set Up the Circuit
Initially, keep the pin6 feedback resistor disconnected and without connecting any battery adjust R2 to get exactly 7.2V at the output of the LM317 (across cathode of 1N5408 and ground line), for powering the IC 741 circuit.
Now simply play with the 10k preset and identify a position where the RED/GREEN LEDs just flip/flop or change or swap between their illumination.
This position within the preset adjustment may be considered as the cut-off or the threshold point.
Carefully adjust it to a point at which the RED LED in the first circuit just lights up......but for the second circuit it should be the green LED that is supposed to get illuminated.
The cut-off point is now set for the circuit, seal the preset in this position and reconnect the pin6 resistor across the shown points.
Your circuit is now set for charging any 6V 4 AH battery or other similar batteries with an automatic cut-off feature as soon as or each time the battery becomes fully charged at the above set 7.2V.
Both the above circuits will perform equally well, however the upper circuit can be altered to handle high currents even up to 100 and 200 AH just by modifying the IC and the relay. The lower circuit may be made to do this only up to a certain limit, may be up to 30 A or so.
The second circuit from above was successfully built and tested by Dipto who is an avid reader of this blog, the submitted images of the 6V solar charger prototype can be witnessed below:
Adding a Current Control:
An automatic current control regulator function can be added with the above shown designs by simply introducing a BC547 circuit as shown in the following diagram:
Circuit#3
The current sensing resistor can be calculated through the simple Ohm's law formula:
Rx = 0.6 / Max charging current
Here 0.6V refers to the triggering voltage of the left side BC547 transistor while max charging current signifies the maximum safe charging for the battery, which may be 400mA for a 4AH lead acid battery.
Therefore solving the above formula gives us:
Rx = 0.6 / 0.4 = 1.5 Ohms.
Watts = 0.6 x 0.4 = 0.24 watts or 1/4 watt
By adding this resistor will ensure that the charging rate is fully controlled and it is never exceeded the specified safe charging current limit.
Test Report Video Clip:
The following video clip shows the testing of the above automatic charger circuit in real time. Since I did not have a 6V battery, I tested the design on a 12V battery, which does not make any difference, and its all about setting the preset accordingly for the 6V or a 12V battery as per user preference. The above shown circuit configuration was not changed in any manner.
The circuit was set to cut off at 13.46V, which was selected as the full charge cut off level. This was done to save time because the actual recommended value of 14.3V could have taken lot of time, therefore to make it quickly I selected 13.46V as the high cut off threshold.
However one point to be noted is that the feedback resistor was not employed here, and the lower threshold activation was automatically implemented at 12.77V by the circuit, as per the IC 741's natural hysteresis property.
6V Charger Design#2
Here's another simple yet accurate automatic, regulated 6V lead acid battery charger circuit which switches off the current to the battery as soon as the battery reaches full charge. An illuminated LED at the output indicates the fully charged condition of the battery.
How it Works
The CIRCUIT DIAGRAM can be understood with the the following points:
Fundamentally the voltage control and regulation is done by the versatile, work horse IC LM 338.
An input DC supply volt in the range of 30 is applied to the input of the IC. The voltage may be derived from a transformer, bridge and capacitor network.
The value of R2 is set to get the required output voltage, depending upon the battery voltage to be charged.
If a 6 volt battery needs to charged, R2 is selected to produce a voltage of around 7 volts at the output, for a 12 volt battery it becomes 14 volts and for a 24 volt battery, the setting is done at around 28 volts.
The above settings take care of the voltage that needs to be applied to the battery under charge, however the tripping voltage or the voltage at which the circuit should cut off is set by adjusting the 10 K pot or preset.
The 10K preset is associated with the circuit involving the IC 741 which is basically configured as a comparator.
The inverting input of the IC 741 is clamped at a fixed reference voltage of 6 via a 10K resistor.
With reference to this voltage the tripping point is set via the 10 K preset connected across the non inverting input of the IC.
The output supply from the IC LM 338 goes to the battery positive for charging it. This voltage also acts as the sensing as well as the operating voltage for the IC 741.
As per the setting of the 10 K preset when the battery voltage during the charging process reaches or crosses the threshold, the output of the IC 741 goes high.
The voltage passes through the LED and reaches the base of the transistor which in turn conducts and switches off the IC LM 338.
The supply to the battery is immediately cut off.
The illuminated LED indicates the charged condition of the connected battery.
Circuit#4
This automatic battery charger circuit can be used for charging all lead acid or SMF batteries having voltages in between 3 and 24 volts.
The above circuit was found not so satisfactory by some of the readers, so I have modified the above circuit for a better and guaranteed functioning. Kindly see the modified design in the below given figure.
PCB Design for the above finalized 6V, 12V, 24V automatic battery charger circuit
Solar 6V Battery Charger Circuit with Over Current Protection
So far I have explained how to a simple 6V battery charger circuit with over current protection using mains input. In the following discussion I will try to explain how the same could be configured in conjunction with a solar panel, and also with an AC/DC adapter input.
The circuit also includes a 4 stage battery status indication feature, an over current controller stage, automatic switch OFF for the load and battery charging, and also a separate cell phone charging outlet. The idea was requested by Mr. Bhushan Trivedi.
Technical Specifications
Greetings, I trust you are well. I am Bhushan, and I am working on a hobby project currently. I am very impressed by the knowledge you share at your blog, and was hoping if you would like to guide me a bit with my project.
My project is around charging a 6V 4.5 Ah sealed battery with grid and solar panel.
This battery will supply power to led lights and a mobile phone charging point. Actually, the battery will be kept in a box. and box will have two inputs for battery charging. These two inputs are solar (9V) and AC (230V) for charging the 6V Battery.
There will not be any automatic switchover. Its like the user has an an option to either charge the battery from solar or grid. but both the input options shall be available.
For example, if on a rainy day or for some reason the battery can't be charged from a solar panel, then grid charging should be done.
So I am looking for an option of both the inputs to the battery. Nothing automatic hereThe battery level indicator LED should indicate in red yellow and green on the battery level.
Automatic battery cut off after voltage goes down certain limits to ensure long battery life. I am attaching a short problem statement along this email for your reference.
I am looking for a circuit for the arrangement shown in it. I am keen to hear from you on this
Kind Regards,
Bhushan
The 5th Design
The required 6V solar battery charger circuit can be witnessed in the diagram presented below.
Referring to the diagram, the various stages may be understood with the help of the following points:
The IC LM317 which is a standard voltage regulator IC is configured to produce a fixed 7V output determined by the resistances 120 ohms and 560 ohms.
The BC547 transistor and its base 1 ohm resistor ensure that the charging current to the 6V/4.5AH battery never exceeds the optimal 500mA mark.
The output of the LM317 stage is directly connected with the 6V battery for the intended charging of the battery.
The input to this IC is selectable via a SPDT switch, either from the given solar panel or from an AC/DC adapter unit, depending whether the solar panel is producing sufficient voltage or not, which could be monitored through a voltmeter connected across the output pins of the LM317 IC.
The four opamps from the IC LM324 which is a quad opamp in one package are wired up as voltage comparators and produce a visual indications for the various voltage levels at any instant, during the charging process or during the discharging process through the connected LEd panel or any other load.
All the inverting inputs of the opamps are clamped to a fixed reference of 3V through the relevant zener diode.
The non-inverting inputs of the opamps are individually attached to presets which are appropriately set to respond to the relevant voltage levels by making their outputs high sequentially.
The indications for the same could be monitored via the connected colored LEDs.
The yellow LED associated with A2 may be set for indicating the low voltage cut-off threshold. When this LED shuts off (white lights up), the transistor TIP122 is inhibited from conducting and cuts off the supply to the load, thereby ensuring that the battery is never allowed to discharge to dangerous unrecoverable limits.
A4 LED indicates the upper full charge level of the battery....this output could be fed to the base of the LM317 transistor in order to cut-off the charging voltage to the battery preventing overcharging (optional).
Please note that since the A2/A4 do not have hysteresis included could produce oscillations at the cut-off thresholds, which won't necessarily be an issue or affect the battery performance or life.
Circuit#5
Adding an Auto-cut OFF on Batery Battery Full Charge
The modified diagram with over charge auto-cut of can be implemented by connecting A4 output with the BC547.
But now the current limiting resistor formula will be as follows:
R = 0.6 + 0.6 / max charge current
Feedback from Mr. Bhushan
Thank you very much for your continued support and the above circuit designs.
I have a few minor changes to the design now, which I would like to request you for incorporating in the circuit design. I would like to express that cost of the PCB and components is a big concern, but I do understand quality is also very important.
Hence, I request you to strike a fine balance between the performance and cost of this circuit. So to begin with, we have this BOX, in which will house the 6V 4.5 Ah SMF Lead Acid Battery and the PCB too.
The 6V 4.5 Ah Battery will be charged either through the followingn options from one single input:
a) A 230 V AC to 9V DC Adaptor (I wish to go ahead with a 1 amp rating charger, your views?) ‘OR’
b) A 3-5 Watt Solar module (Max Voltage: 9 V (6V nominal), Max Current: 0.4 to 0.5 Amps)
Block Diagram
The battery can be charged by only one supply at a time hence will only have one input on the left side of the box.
For the time when this battery is being charged, there will be small red led light which glows on the font face of the box (Battery Charging Indicator in diagram) Now, at this point, the system should also have a battery level indicator (Battery level Indicator in diagram)
I wish to have three levels of indications for the battery state. These tables state the open circuit voltage. Now with the very little electronic knowledge I have, I am assuming this is ideal voltage and not the actual conditions, right?
I think I will leave that on you to decide and use any correction factors if required for calculations.
I wish to have the following indicator levels:
- Charge level 100% to 65% = Small Green LED is ON (Yellow and Red LED off)
- Charge level 40% to 65% = Small Yellow LED is ON (Green and Red LED off)
- Charge level 20% to 40% = Small Red LED is ON (Green and Yellow LED off)
- At 20% Charge level, battery disconnects and stops supplying output power.
On the Output side now (Right Side View in diagram)
The system will supply power to the following applications:
a) 1 Watt, 6V DC LED Bulb – 3 No’s
b) One output for Mobile Phone Charging I wish to incorporate a feature here. As you see, the DC loads connected to the battery are of relatively less wattage. (just a mobile phone and three 1 watt LED Bulbs). Now, the feature to be added in the circuit should kind of work as a fuse ( I don’t mean an actual fuse here).
Assume if a CFL bulb is connected here or some other application of higher wattage rating, power supply should be cut off. If the total power drawn is in excess of 7.5 Watts DC connected to this system, the system should cut off supply and shall only resume when the load is below 7.5 Watts.
I basically wish to ensure that this system is not misused or drawn excessive energy from, thereby damaging the battery.
This is just an idea. I do however understand this can potentially increase the complexity and cost of the circuit. I will look for your recommendation on this on whether to include this feature or no as we already are cutting off the battery supply once the state of charge reaches 20%.
I hope you find this project exciting to work on. I look forward to receiving your much valued inputs on this.
I am thanking you for all your help till now and in advance for your extended cooperation on this.
Kind Regards,
Bhushan.
The Design
Here's a brief explanation of the various stages included in the proposed 6V battery charger circuit with over current protection:
The left side LM317 is responsible for producing a fixed 7.6V charging voltage across its output pin and ground for the battery, which drops to around 7V via D3 to become an optimal level for the battery.
This voltage is determined by the associated 610 ohm resistor, this value can be reduced or increased for changing the output voltage proportionately if required.
The associated 1 ohm resistor and the BC547 restricts the charging current to around a safe 600mA for the battery.
The opamps A1---A4 are all identical and perform the function of voltage comparators. As per the rules if the voltage at their pin3 exceeds the level at pin2, the corresponding outputs become high or at the supply level..... and vice versa.
The associated presets may be set for enabling the opamps to sense any desired level at their pin3 and make their corresponding outputs go high (as explained above), thus A1 preset is set such that its output becomes high at 5V (Charge level 20% to 40%)....A2 preset is set to respond with an output high at 5.5V (Charge level 40% to 65%), while A3 triggers with a high output at 6.5V (80%), and finally A4 alarms the owner with the blue LED at battery level reaching the 7.2V mark (100% charged).
At this point the input power will need to be switched off manually since you did not demand for an automatic action.
Once the input is switched off, the 6v battery level sustains the above positions for the opamps, while the output from A2 ensures that the TIP122 conducts keeping the relevant loads connected with the battery and operative.
The LM317 stage at the right is a current controller stage which has been rigged to restrict the output amp consumption to 1.2 amps or around 7 watts as per the requirements. The 0.75 ohm resistor may be varied for altering the restriction levels.
The next 7805 IC stage is a separate inclusion which generates a suitable voltage/current level for charging standard cell phones.
Now, as power is consumed the battery level begins receding in the opposite direction, which are indicated by the relevant LEDs....
Blue is the first one to shut off illuminating the green LEd, which shuts off off below 6.5V illuminating the yellow LEd which identically shuts off at 5.9V making sure that now the TIP122 no longer conducts and the loads are shut off....
But here the condition may oscillate for some moment until the voltage finally reaches below 5.5V illuminating the white LEd and alarming the user for an input power switch on and commence the charging procedure.
The above concept can be further improved by adding an automatic full charge cut off facility, as shown below:
With over 50,000 comments answered so far, this is the only electronics website dedicated to solving all your circuit-related problems. If you’re stuck on a circuit, please leave your question in the comment box, and I will try to solve it ASAP!
Hello sir,
In my project i need to charge multiple batteries using switching circuit. from dc load one charger and same charging for 2 split batteries, charged battery will light the load when required. when dc source is not available. tell me how can i do this. give me your contact details
Hello Sheela,
I guess you are referring to a battery charger circuit that will charge two batteries alternately depending on which is fully charged or discharged.
You can refer to the Last circuit diagram from the following article using two op amps
https://www.homemade-circuits.com/automatic-dual-battery-charger-with/
I have a question about the automatic full charge cutoff in the last couple circuits. The output at the A4, pin 14 is connected to the transistor, but won’t it slowly let more and more current through as it approaches the desired charge? And consequently, won’t the output of the lm317 drop too as current starts to flow across the transistor, lowering the reference voltage? I guess I am failing to see how the battery will ever reach the desired charge. I would be delighted to hear what is wrong with my thinking. Really enjoyed reading about the design process. I am currently a student and I learned a lot.
The A4 pin14 will not change slowly rather it will change from 0V to 7V instantly and shut down the LM317, cutting off the supply to the battery. Op amp outputs are not designed to change state slowly, rather their output change state with a snap.
So when the 6V battery reaches its full charge level, let’s say 7 v, at this point the A4 input detects the full charge level and its output instantly changes state from 0V to 7 V shutting down the LM317 and cutting off the charging supply to the battery.
Please let me know if you have any further doubts or questions.
Hello sir, thank you for your sharing, I need the automatic cut-off charging circuit, but I cannot find the exact equivalents of some components (lm324) in the proteus isis program in the last circuit you shared, I request you to share the proteus files of this circuit or an alternative circuit.
Hello Murat, Sorry, I don’t proteus file for any of the above circuits. LM324 is a very common and standard IC and is most suitable for this application. You can try two LM358 ICs if you are having problem with LM324.
Good day, Sir. I would like to ask for your help. I’m planning to design a battery charging circuit for a microbial fuel cell that will possibly run an operating maximum voltage of 425mV. I would like to charge a battery of 12V and 8Ah. The battery will be used for charging a flashlight and a cellphone with micro USB charging port. Thank you very much for your help.
Hi Ish,
for your 12 V, 8 Ah lead acid battery you can simply use an LM338 based charger as shown below:
Just makes sure to replace the LM317 IC in the diagram with an LM338 IC.
Next, adjust the pot to get an exact 14 V at the output for the battery, and calculate the RC to get around 1 amp at the output. The battery might take around 10 hours to get fully charged. For the transformer you can use a 9-0-9V transformer and use the 9-9 V taps for feeding the bridge rectifier.
Hello again, sir. Thank you for your reply. What if I want a DIY dc to dc booster to charge a 12V 8Ah battery? Like, around 400-500mV (maximum operating voltage from MFC) into around 9V.
Hi Ish, Charging a 9 V or 12 V battery from a 0.5 V source is almost impossible. Even a boost converter might not work correctly with a 0.5 V source.
Moreover, to charge a 8 Ah battery, the 0.5 V source must have a current output of 30 amps.
Hi. How about using an op amp LT1366 with the same 0.5V source? Is it possible to charge a cellphone battery? Thank you.
LT1366 needs a minimum of 1.8 V to operate and also the input source would need to have at least 8 amp current to charge a cellphone battery
Thank you for your replies. I really appreciate that you’re giving such a valuable time to answer my inquiries. As of now, I read an article at which they use a MCP1643. Can you tell me if it is possible for this microchip to be used for the same 0.5V source for cellphone battery charging or it is only good for LED booster?
You are welcome! You can try this IC, it might work! However, the cellphone battery will require at least 500 mA current to charge. This means your 0.5 V source must be able to generate at least 4 amp of current.
Hello Sir.
Please I can not find resistor 610ohms in our local market here, what can I do, or can I go ahead and use 680ohms ?
Hello Engr Bayo,
You can use the following software to calculate and adjust the desired R1, R2 values for getting the 7.6V output for the battery, after D3
https://www.homemade-circuits.com/lm317-lm338-lm396-calculator-software/
Dear Sir,
I use five LI-Ion batteries 3,6V 2000mAh in series to make a battery pack for my 18V cordless drill . Which circuit I should use to make a proper charger for it? I have looked trough those circuits and I am confused with power supply and zener voltages.
Thank you in advance.
Nedzad Niksic
Hello Nedzad, you can charge your battery simply with an LM338 variable regulator circuit. No need of complex opamp stage. You just have to adjust the output of the LM338 power supply to a point which is marginally lower than the full charge voltage of the battery. Once you do this the LM338 will charge your battery safely without the need of any auto cut off. To monitor the charge level you can attach voltmeter across the battery terminals.
Dear Sir,
I have maid simple charger for 18V battery, using LM338 variable regulator circuit only, as you suggested. I would appreciate if you help me to make a LED indication for fully charged battery. I guess by addition of a transistor.
Thank you in advance.
Nedzad Niksic
Hi Nedzad, you can probably build one of these circuits which are discussed in the following article:
https://www.homemade-circuits.com/battery-full-charge-indicator-circuit/
Sir,
I have made the first circute (having relay) with the same pcb layout given. Every thing is fine but the charging green led is always on when the 6 volt battery is connected to the circute. Could you please help me.
Midhun, try adding a diode in series with the emitter of the BC547. Anode of the diode will go to the emitter, and cathode to the ground line.
Alternatively, remove the green LED and replace it with a jumper link, and add the green LED with a 1k series resistor parallel to the relay coil.
Also make sure to add a 2k2 resistor between base emitter of the BC547
Sir thanks for your valuable reply.
You are welcome!
Hello Sir,
Is it possible to add to this design a modification to protect the battery charging system
on a 1975-80 Honda CT 90. This would help a large group of people.
Thank you for your time.
Hello Joseph, the battery will be well protected in all the above described circuits….
Hi,
This website is an excellent initiative that both helps and encourages hobbyist like me. I appreciate the efforts of swagatham.
Need an information on the pcb layout of the 1st circuit giive ( I mean the one with the relay ). Could you share the measurement ( length and width of pcb pls ). It appears scaled when printed out, so need to restrict to the actual scale.
Thanks!!
Thank you Priyan, glad you are finding my articles useful….
The easiest way to resize the PCB to the correct dimensions, is by matching the pinouts of an actual relay on the computer screen. The PCB size that perfectly matches the relay pinout distance will fix the real dimension of the board
You can punch the holes of the relay on a hardboard and then press the area over the PCB layout on your computer screen and keep adjusting the PCB dimension until the holes match correctly.
Hello Swagatam,
Your suggestion to have relay dimensions as reference to scale the print out worked well.
Thanks!!
Thanks Priyan, glad it solved the problem!
Is the PCB with components mounted available for sale?
I would like to buy 2 to 5 boards.
Sorry, we don’t sell parts or kits in this website!
hi.
for the second circuit without relay.
I got this circuit, I couldn’t.
Whereas it was very necessary for me
for the second circuit without relay
6v- 4 ah
for 4 Ah, a 400 mA current would be perfect, lower current than this will prolong the charging time upto 15 to 20 hours.
So a 500 mA is the nearest and the most favorable current for your application.
And please do not increase the maximum voltage above 7.2 V
Hi, I like your work. My name is Joakín. And I want to do an adjustable charger 3V to 85V 3A, with automatic turn off for 14V, 27V, 42V, 56V, 70V and 84V and automatic adjustable 1A to 3A charge control. Would you be so kind to help me with the circuit and explanations.
The best for you and your´s.
Joakin
Hi Joakin, I am glad you liked my work. You can probably try the following concept for your specific application:
https://www.homemade-circuits.com/regulated-car-battery-charger-circuit-for-garage-mechanics/
For getting the specified 6 voltage ranges, you will have to replace the S1 switch with a 6 way rotary switch…and then add more number of the respective zener diode/diode stages for each of the contacts of the rotary switch, depending on the max voltage levels. You will also have to add the 1k presets for each of these arms for enabling the fine tuning facility for each of these voltage adjustments.
Also, make sure to change the BD138 with TIP30CG, BC547 with ZTX853, and BC546, BC557 with ZTX553
Yotta thanks for your answer.
I´m trying to do an universal charger for Electro bikes, for Liion and Gel-acid batteries in different voltages.
I´ll see what you suggested to me.
Thans so much
Joakín
No problem, wish you all the best with the project!!
for the second circuit without relay.
Energy input to lead battery 0.18 A.
If this is the problem how can I fix it?
what is the battery Ah value?
hi.
for the second circuit without relay;
When I set R2 to 7.2v, the energy input to the battery becomes 6.4v.
When I set R2 to 8.3 volts, the energy going to the battery is 7.2v.
Hi, the input voltage will always drop and settles down to the discharge level of the battery. It will start increasing slowly up to the 7.2 V mark as the battery charges.
Make sure the input is 10% of the battery Ah value for a lead acid battery, and is 50% for a Li-Ion battery.
hi.
for the second circuit without a relay;
I’m adjusting 10k until the red led turns off.I’m doing R2 7.2 volts.After doing everything, the red led lights up as soon as I connect the battery cable.As soon as I pull the positive cable of the battery, the red led turns off.and the voltage of the outgoing cable to supply the battery is up to 5.5 volts.room shouldn’t be 7.2v?
What am I doing wrong.
thank you
Hi, for the second circuit, the red LED should illuminate when the battery charges upto 7.2V. Because at this voltage the pin2 should go above the pin3 voltage level.
So long as the battery voltage is below 7.2V, the pin2 voltage will be lower than pin3, which will keep the output pin6 high and the green LEd will be illuminated.
Once the battery level goes past 7.2V, the pin6 will become 0V. illuminating the red LED and shutting off the green.
hi.
I want to charge a 6v-4 ah battery.
I want it to stop charging when the battery is full.I want it to automatically cut the charge when the battery drops to 6 volts.
Which circuit do I need to use this without relay?
The cable of energy to the battery will always be connected.Please I ask you to recommend a circuit accordingly
I thank a wise like you very much.
Hi, I have explained the details in the above article, I would recommend you to go through the whole explanation and then proceed accordingly.
Hi Swagatam Sir,
query CIrcuit#2(without relay):
After adjusting preset 10K to flip flop position between green and red led at which position to leave preset green ON or red ON before reconnecting 100K resistor.
thanks in advance.
Hi Muzzanil, initially keep the preset center arm to ground level. Disconnect the 100k feedback. Apply the full charge level, which should turn ON the green LED with red switched OFF. Now slowly turn the preset until the red turns ON and green turn OFF….that’s all the circuit is set now. Connect the 100k feedback link into its initial position.
Hello Swagatam Sir,
query Circuit#2(without relay):
when battery(6V 4.5Ah) is charged full which led should remain ON.
I have built circuit and when I check voltage across battery terminal while charging
below 6V Green ON Red OFF
above 6V Green ON Red ON TIP122 OFF(checked by continuity testing across pin 2(collector) and pin3(emitter) of TIP122) charging current drops to 10-20mA
please help where I am wrong.
Hello Muzzamil, when the battery is switched OFF the current will drop towards zero….use LM358 op amp instead for ensuring that only One LED lights up at a time…
Hello Swagatam Sir,
what other changes needs to be done if I replace ic 741 by LM358 in “Circuit#2(without relay)” will schematic change.
in current circuit(set at 7.3V) red led is ON as soon as battery reaches 6V.
I want red led to glow when battery reaches 6.4V
thanks in advance.
Muzzamil, no changes will be required for LM358, you can use the same circuit. For 6.4 V cut off adjust the preset to get the changeover at 6.4 or 6.5 V threshold.
Hi Swagatam sir,
thank you for the support.
tried this circuit using LM358 still no luck. Red and green led both keeps glowing when battery reaches above 6V.
You said above circuit is tested, so is it tested physically with battery or on PC run simulation.
Hi Muzzamil, this website is about learning electronics, so please investigate your circuit and find out why both the LEDs are ON in your circuit?
You can take the help of this video, and build this basic set up first and try to understand the op amp behavior.
https://www.youtube.com/watch?v=phPVpocgpaI
You can also try the second last circuit without a feedback to check whether your basic circuit is OK or not:
https://www.homemade-circuits.com/usb-automatic-li-ion-battery-charger/
In the Circuit#2:
Across which pin we have to set 7.2V.
Here confusion is there because if I set 7.2V across LM317 then same voltage is not shown on battery terminals(battery not connected).
It would be really helpful if you can mark on circuit and show image across which point to set 7.2V
Thanks in advance.
Hi, thanks, I have updated the description with the required information…it should be between the cathode of 1N5408 diode and the ground line.
Thanks for reply. I understood it.
Dear Mr. Swagatam ,
I am very grateful to you for this project. This charger with an IC is very interesting.
I have a question, will this circuit work for other kind of LeadAcid batteries (6V7.3Ah or 12V7.3Ah) that are connected to a circuit? I want the my circuit to be connected to the battery and the battery to be connected to the charger. The solution is somehow simple (connecte the charger to the battery) while the circuit is still connected or I have to do some adjustments?
The circuit current consumption is around 200-250 mAh and once a hour it has as spike that can go up to 2Ah for 5-10 seconds depending on how fast the GSM shield is finishing it’s task.
Dear Andrei, yes this circuit can charge all types of batteries below 30 V and 50 Ah.
For your application you can modify the transistorized desigbn in the following manner:
Dear Mr Swagatam,
I have read many interesting articles and solutions from you for requests made by visitors/addicts of your website. I would like to know if it is possible to change these circuits to be used as follows;
I have a dashcam in my car and I am searching for a solution. When the car is running, the dashcam gets its power, 5 volts, from the car battery. Meanwhile the car battery is charging a powerbank. The moment you turn off the car the powerbank needs to power the dashcam. If the sun is out, the solar panel provides power to the powerbank. The dashcam itself has a small battery of its own. The powerbank are some li-ion cells from an old laptop battery pack. I have been thinking of a cheap solar charger from china but these are unreliable and produce a lot of heat which is a waste of power. I am sorry if I did not search very well and did you already create such a schematic.
Dear Robert, A PWM based charger works best for any solar charging application. Although there are plenty of pwm chargers designed by ti.com, the following one looks perfect for most applications.
PWM Inverter Using IC TL494 Circuit
Dear Swagatam,
Thank you for your reply, but that solar charger is not what I am looking for.
I am trying to find something like a Hybrid Solar Charger Circuit to charge lithium batteries.
Or alter an existing circuit to suit my needs.
Input 12v car system and 6 or 12 volt solar panel.
Output for the batteries and charge controller should be 5 volts and a few amperes ( 2 to 5).
Sir, is it possible to add that feature or modify one of your designs.
Hi Robert, there are a few examples in the following article which may suit your purpose:
https://www.homemade-circuits.com/simple-dc-ups-circuit-for-modemrouter/
Dear Swagatam
For circuit number 3 can I use an mje13009 instead of tip122 because this is what I have in hand. Will I need to bring some kind of modifications after doing so?
Thks & Rgds
Aslam Chumroo
Hello Aslam, It won’t be an appropriate selection, but it might work, although not as efficiently as a TIP122. You may have to add a 2N2222 with it to make it a Darlington type. No other parts will need to be changed
OK.. I discovered an mje3055 hanging around in my house. I believe it is a better option because it has a higher current gain.. But I like your idea of using a 2n2222 to form a darlington because this will boost the current gain. Thks
Dear Swagatam,
I am trying to build circuit #3.. I do not have the 3V zener diode. Instead can I use a tl431 and configure it to output 3V?
Thank you
Hello Aslam, you can use any form of fixed reference for pin3 and TL431 would be fine, although zener diode is a much easier option.
Thank you sir
Hi, dear
PLEASE CONNECT A 10uF ACROSS PIN2 AND PIN4, SO THAT THE OP AMP OUTPUT ALWAYS BEGINS WITH A “HIGH” ON POWER SWITCH ON
If I understood the circuit should it look like this, tell me if i’m wrong?
https://imgur.com/a/ogFvjni
Can I charge a 4.5Ah battery with this circuit?
That looks oK to me, pin4 is also the ground line of the circuit
Thanks Swagatam, I will be doing a PCB Layout for this circuit soon.
Hi dear, I made PCB Layout for this circuits.
Warning: download the file within 30 days, after which the file is automatically deleted.
https://easyupload.io/q269w9
Hi thanks, but I cannot open the PCB design in my computer
Hi, you must have EAGLE 7 installed to open Design, Download the new .RAR file, I Made a PDF version 1:1
I would love for you to make a detailed video on this topic.
Warning: download the file within 30 days, after which the file is automatically deleted.
https://easyupload.io/qnomyn
OK thanks, I have taken the screenshots and updated them in the above article.
Sure, a video clipping will be greatly appreciated.
Hi Jack009,
Could you upload the PCB layout and share me a link please. The one shown in this page is scaled to bigger size so couldn’t transfer that to copper clad.
Thanks
Priyan
Or the actual size ( width & height ) of the image if given will help to manually scale in the image while printing out.
Thanks!!
ok so if i want to use 0.06 ohm’s. how many 1 ohm’s am i going to connect in parallel in other to get 0.06 ohm’s.
You will need 16 resistors
Sir is about the circuit no #3 my Rx is 0.1 ohm but due to the resistor is not in the markert you told me to connect 0.06 ohm in parallel but yet this 0.06 ohm’ is not yet to be found. pls sir any other suggestion on what to do concerning this resistor. waiting for your respond.
Youngking, I never said that, I actually said the opposite. Please read my comment correctly.
For 0.1 ohm, you can connect 10nos of 1 ohm in parallel
Pls sir don’t be bore with my question. How will i by pass the relay contact with wire link and more over there are two preset in that circuit, will i only make use of only 10k pot when doing the adjustment pls clear me on this. Thanks
The preset associated with LM317 is for adjusting the full charge level at the cathode of the 317 output diode.
The op amp preset is for adjusting the full charge cut off.
for bypassing the relay just short circuit the pole and the N/O contact of the relay. Do not connect any battery while doing the setting up procedure….
so if i may understand what you mean after i apply 14v from variable power supply to the input of lm317 i will remove N4148 diode and adjust the 10k pot until th green led is off , after that i will still turn the 10k preset that is is connected with ic741 until the red led is on before connecting back the feedback diode. is that what you mean.
If you want to use the LM317 supply itself, then you must adjust its output at the battery full charge level, then bypass the relay contacts with a wire link, and then adjust the preset EXACTLY as I mentioned in my previous comment…1N41418 feedback must be removed before applying power.
Make sure to remove the bypass link after the adjustment is complete and also reconnect the 1N4148
Hello sir, thanks for your quick respond but i have one more question concerning this last circuit #3 that uses relay, pls sir explain how i can set this circuit using variable power supply. Sorry for asking too much.
It is the same as other op amp battery chargers designs presented in this blog, remove the 1N4148 feedback diode, adjust the 10K preset to ground, apply the full charge voltage from a variable supply across the supply terminals of the op amp, adjust the preset until the Green LED is switched OFF and RED turns ON. Finally, reconnect the feedback diode
Good evening sir, pls sir i have few quetion concerning the circuit last circuit #3 base on the calculation you gave . 1- if am to charge 12v 75ah to 100ah lead acid battery, so my calculation will be 0.6/10=0.06 0.6×10=6 which means Rx=0.06 ohm’s 6watts resistor while 10 is my battery current, but the problem is that i can’t find 0.06 ohm’s resistor and ic lm338 in the market any help. Pls correct me if my calculation are wrong. (2. I know that setting this circuit will require a varible power supply pls explain the setting clearly. (3. Like you said that all your battery cutoff act as a switch so does it mean that using solar panel with this circuit as a source that one has to include transformer and rectified diode pls explain. Lastly where will i turn my dial to when measuring current using my small multimeter. Pls sir i’m waiting for your respond. Thank you.
youngking, you can use connect 2nos of 0.1 ohm in parallel to get 0.05 ohms….for 10 amp you must use LM396, LM338 will not work.
How can you use a transformer with a solar panel? The output from a solar panel is already a DC.
Without knowing your multimeter specs I can’t suggest much!
Hi, Sir
How to limit max current to 400mA in this version:
Can i use 220R instead 240R?
Hi Jack, please see the last diagram, and add the BC547 and Rx stage to the LM317 appropriately.
yes 240 ohms will also do insteda of 220 ohm
Hello Sir,
I have made the last circuit posted by you, and I have made changes to it to make it for 12V battery, 6V zener instead of 3V (Z1) and I’ve also replaced the 610ohms resistor with 10K preset to adjust the charging voltage whenever I require. I need 16V output to from LM317 to charge my battery faster and I am using a 18V 2A SMPS to the input of LM 317. To adjust the input voltage I am using a variable power supply, and I am unable to adjust it to 16V output at 317 when i give 18V input to the same. The problem that is happening is the output is reaching at 14V when i apply 16V input and as I increase this 16V input further, the output of 317 starts dropping from 14V to 13V and then cuts off to 1V or something. Please provide a solution for this.
Hello Sagar,
The LM317 is itself is a variable regulator IC, so an external variable supply is not required. You can supply the 18V directly to the LM317 input, and set the LM317 pot for the battery.
However, the voltage is never responsible for fast charging, it’s the current that determines the charging rate. But if a high initial current is used it must executed step wise through a step charger circuit….otherwise it can cause permanent damage to the battery.
The recommended current is 1/10th Ah value if a step charging is not used, and at this current level it does not matter whether the input is 14V or 16V especially when the cut off is set at 14.2V
So you must set the LM317 output voltage to 14.5V, and the cut off at 14.2V, and the input can be 18V from the SMPS.
If the input has higher current than the recommended value, in that case you can limit it by using the 4rth circuit from top, through Rx.
Can you please provide the step charging circuit as you mentioned? I want to charge the battery fast! Please help.
you can try this concept
https://www.homemade-circuits.com/fast-battery-charger-circuit/
Hai Sir,
One small doubt in circuit 3 sir…
0.6/0.4=1.5ohms
0.6/0.4=0.24ohms
How u calculate 0.24ohms sir..
If i calculate ,1.5 ohms value coming sir..
Pls clarify it sir
And how to calculate resistor wattage sir
Thank u sir
Thanks Kesavraja,
Yes it is 1.5 ohms, I have corrected the calculations in the article, and also added the wattage value under it. Please check it out now.
Ok sir Thank you.
3.7v 2400mah
for a 3.7 V cell I would recommend the last circuit from the following article:
https://www.homemade-circuits.com/usb-automatic-li-ion-battery-charger/
what will .be the changes
Please provide detailed specification of your Li-Ion cell….
can i use the last circuit to charge liion battery
yes you can, try the last one.
Please how can I use a MOSFET in place of relay, thanks
Replace the TIP122 with MOSFeT
Dear mr Swatagam’
I am gratefull for all your project. Everything I have in mind to do you are done.
Thank you . I am engineer of electronic too but in poor condition with many resurces
top of that now is time because I am retired. But that project like this make me happy and full my time
and mind. In circumtances of ilnest is great light in the end of tunnel when I finish some of yours
project and it works sucsesfull. joy for me, thank you.
for ideas energy focuss
when finish project i told you
see ya or read ya
petre
No Problem Petre, I am always there to assist you! Wish you all the best…and please keep posting!
I have been trying to make this circuit, But the charging LED doesn’t seem to wok for some reason, Please help me out with it
Is it only the LED that’s not illuminating or the entire circuit not functioning? Try removing the 1N4148 feedback link and check again.
can you contact me via email or whatsapp please? I have too many doubts regarding the circuit.
Only the red Charging On LED is not working. Also The cutoff happens at 4.3 volts instead of 5
Which circuit have you built?
The last one.
You will need a variable power supply for the setting up procedure. Initially do not connect the mains input or the battery. Rotate all the presets to ground side. Apply 5V across pin#4 and pin#11 of the LM324.
Adjust the lowest opamp A1 preset such that the white LED just illuminate.
Increase the voltage to 5.5, adjust the A2 preset such that the yellow LED just illuminates.
Again increase the voltage to 6.5V, adjust the A3 preset such the green LED just illuminates.
Repeat the same for A4 with a voltage of 7V until the blue LED just illuminate. When blue lights up RED will shut off.
That’s all the circuit is set up now. Remember the output after D3 should be 7.2V, so adjust R2 near LM317 accordingly.
This is the correct setting up procedure, I hope you understood now
You can freely discus the problems here, I will solve them all step by step, the concept above is very simple, so it won’t be a problem.
I made the circuit and converted it into 12Volt by using 6V zener instead of 3V zener and connected it to a 12V 7Ah battery. At initial stage the battery was 12.05V. then I checked the battery Voltage after 19Hours, the battery voltage dropped to 11.71 Volts. Is this circuit supposed to use the battery this much? What are the options to reduce this drop? Also, Only the circuit was connected no load was connected.
If you made the last circuit, the LEDs will give you direct indications whether the battery is charging or not.
Which circuit did you make? How did you adjust the preset? What voltage and current did you apply?
Give all the details for getting proper solution!
I made the last cricuit. The fully updated one. And used the procedure as explained by you before. but for 12V system. I just want to know if this circuit will lower the battery in idle condition.
Yes it will discharge the battery if it’s connected for a very long time, you can eliminate this by removing D3 and by connecting it in series with the battery positive line, as done in this diagram:
I want to have charging auto cutoff in your last 6v battery charging circuit having mobile charging facility.
Waiting for reply
I have updated the required diagram at the end of the post, you can check it out!
Thanks a lot
I m looking for circuit 3.7v / 5200mah lithium ion battery charger from 12v solar panel with battery level indicator & charging full & lo battery load cutoff
In the last circuit replace both the LM317 ICs with LM338. If the load is not a power LED you can eliminate the right side LM317 and replace it with the wire link.
Also, replace the 1 ohm resistor by solving this equation: 1.2 / desired charging current
Can we have Load cutoff indicator in 6v battery charger
when the yellow LED shuts off and white illuminates it means load is shut off
I m looking for 3 stage 12v/7ah 12v/18ah solar battery charger with hi & lo voltage cutoff & battery level indicator
You can try these two circuit:
https://www.homemade-circuits.com/fast-battery-charger-circuit/
https://www.homemade-circuits.com/make-this-3-step-automatic-battery/
Why 470ohms 1/4 watt resistor connected permanently to +terminal of battery in 741 IC used charger circuit?
To keep the battery trickle charged continuously once the charging is over!
Thanks
One 100uf capacitor connected between transistor BC547’s base and negetive line in #circuit1.what is the advantage that?
To enable a stable operation of the relay changeovers.
sir,
I have successfully built one of your project ‘ pwm inverter using sg3525 ‘. Now I wants to include the charger circuit no.3 to the inverter circuit. Since the circuit is for 6volt battery, will it be compatible for the inverter of 12volt battery. If so what are the changes to be made. Pl. kindly suggest me sir. Is ziner diode of 3volt is to be substituted with 6volt?
Thanking you sir.
Leelesh.
Hi BK, I am glad you could build it successfully.
you can use the same circuit for charging 12V battery also. You can use a 6V zener if you wish, although a 3V will also work without issues.
If your battery is higher than 10 Ah, then you can replace the LM317 with a LM338
Sir,
I can’t find 741 IC, 2N2219 and LM338 instead i found HA17741 IC, TIP41C and LM317T
is there any changes in the final circuit sir? the battery is 12v 50Ah.. thanks a lot sir..
Hi Paul, those parts will also work without issues, however TIP41 can be unnecessarily big for driving a relay, you can try any other small signal transistor such BC547, or 8050, or BD139.
By the way for a 50 Ah battery LM317 won’t work , and won’t be required also. You can use a 0-12V 5 amp or 7 amp trafo, rectify the output with a bridge rectifier and a 2200uF/25V filter capacitor, and feed the DC to the opamp circuit, ….at the anode of the left side diode. This diode must be rated at 10 amps.
Also for the 1N4148 diode, use two in series.
Sir i cannot see the relay in the finalized circuit where it will put? and the 1N4148? im going to make the modified finalized circuit?
OK, if you want to use the last diagram, you can build it with your available parts, but TIP41 will not respond correctly with the opamp output. You will have to reinforce it with another NPN in a Darlington configuration. It can be a BC547 or any similar. TIP41 will also need a good heatsink.
Sir is 104/50v electrolytic capacitor and can I use 3.6v zener instead of 3.3V?
Ken 104 is not electrolytic, it is ceramic, yes 3.6V will do
Thanks for the reply sir.. C1 is also 104 / 50v ceramic cap. sir? and is it possible to use TDA2822 audio I.C instead of 741?
yes it is also 104/50V but it is not crucial…TDA may work, but that would be an awkward way to use an audio amplifier IC, actually I am not very sure about it!
Hi Swag,
In the 3rd circuit, the one corrected, what changes do I have to do in order to charge 3 6V/4.5AH batteries connected in parallel?.
Thanks.
Best Regards,
Nélio Abreu
Hi Neilio, you won’t require any changes, just make sure that the input supply current is not over 2 amps.
Hi,
Ok. Thanks
Best Regards.
Nélio Abreu
Hi Neilio, forgot to tell you, please make sure to add separate diodes for each battery, as shown in the following article.
https://www.homemade-circuits.com/connecting-batteries-in-parallel/
Hi Swag,
Ok. Thanks for the notice.
Best Regards,
Nélio Abreu
i have 12V dc battery and 7A/h current ratting please give me the correct circuit as soon as possible.
You can try the first circuit from this article:
https://www.homemade-circuits.com/how-to-make-current-controlled-12-volt/
Make sure to adjust R2 to get exactly 13.9V, and select Rc as 0.6 ohms 1 watt
Hi sir I’m Yogesh .6v/4.5ah ka Jo circuit h usme 12v off karneke bad green led battery supply pe on hi raheta h to usko disconnect kaise karneka .plz help me .
Hi Yogesh, the green or red LED will be ON if the battery remains connected, because the LEDs will indicate the immediate status of the battery, green will indicate that the battery is not fully charged and red will indicate it is fully charged….so that’s part of the circuit and it is correct.
I want to fabricate a 12v, 3.5 Ah Nimh bty charger. I’ll be grateful if you send me the cct diagram with description.
you can make use of the 3rd circuit and use it for your purpose…just make sure to supply the correct specified amount of current from the input side, and set the preset accordingly for the cut off
Hello Swagatam, I am facing great issue every time to take out the battery from my nokia x2 to charge and your charger circuits are very promising and I even built a skeleton circuit with the design with two bc547, will check out..but, we all need fastest charger, and nearly everything I used so far, universal charger etc. plus your schemes, provide very little current and rate, 150ma or so. So I have to wait six to seven hours for fully charging! The reason is stated that liion batteries keep good health if charged very slowly, but again, liion has advantage of charging almost equal rated current as its Ah. Even, companies, in my case, microsoft, provides charger with rated current 600 ma. So I need a design with simplest scheme with charging current around 1-1.5 A, using 555ic or tl431and any regulator ic 317, 7805etc, I am not much into zener diodes ) and your charger design with two bc547 lacks charging led indicators, so these in new design will also be welcomed. I can buy 4056 module, that comes with a 1A promise, but, I want to make something myself also the components at my disposal needs to be used. Thanks for your time.
Hello Indrajit, I never said that Li-ion battery must be charged slowly. This is true only for lead acid battery not for Li-ion.
None of my circuits are designed to restrict current to a fixed level or to 150mA, it depends what input supply you apply. All The auto battery cut-off circuits which I have explained only act like a switch and will never drop current by itself.
It completely depends on the input supply current that you use and ofcourse your battery health condition, if your battery is bad then it will never consume current at the correct fast rate, regardless of which charger you use.
For more info you can red the following post:
https://www.homemade-circuits.com/constant-current-source/
By the way which charger circuit are you referring to??
Hi, how to control the charging current to the battery with the third circuit? Because the LM317 in the above circuit acting as voltage regulator. I need to charge a 12v, 1A battery with the above circuit which require 100mA for charging?
Hi, you can add a BC547 transistor stage as per the following article diagram:
https://www.homemade-circuits.com/how-to-make-solar-battery-charger/
ok. Can I use the third circuit for 12v battery? Do I need to change any components for that? Will the 3v zener fine for 12v charger?
In 3rd circuit, Pin 2 and Pin 3 is interchanged when compared to your other battery charger circuit? Is that correct?
you can make the third circuit, no components needs to be changed, the pin#3 zener can be any zener between 3 and 9V.
here pin#2 and pin#3 are swapped because a relay is not used, transistor is used directly for the cut-off… so the triggering needs to be opposite, and is correct.
Hai sir…
I try lm317 charging circuit for 6v 4.5ah battery….
I try only charging section not auto cutt off section..
Input i use 12v 1.5ampere adapter….
I adjust the output voltgae 8v…
Now battery is charging…
But ic heat sink more heat..can’t even touch it….
After few hours the ac adapter power led auto off and on.when adaptor output voltage got short it only the led off..but here i check the connection all proper
.i check the 317 output voltage…its decrease and increase.like
2.5v,3.4v ,4v,5.23v,6v continues …
When i remove battery the lm317 output voltage good…i think that battery may be damage ,so i check with another battery same think happening
So i change Ic …half hour charging well afterwards this problem continues…
And also i change adaptor….
But this problem continues when i connect to battery..
Without battery its working good…
Guide me sir…
Hi Kesav, it may be happening due to the IC getting overheated, which is never good for any IC, you must use a large adequate amount of heatsink to control and dissipate heat appropriately. and also make sure that the battery is getting charged with a correct ampere rate, for a Lead acid battery it should be 1/10th of its AH, exceeding this will be bad for the battery and also for the controller circuit if its not rated to handle this.
Thank u sir….
I will rectify and tell u sir
ok..
Sir today i check it ampere ratings of transformer…
12v 2ampere transformer output showing 6 ampere in DC AMPERE in multimeter out of 10.
12V 3 Ampere transformer output showing 9.47 Ampere sir..
I think that multimeter may be faulty..so I check with another one multimeter also showing the same results….
While charging battery when i check ampere it shows only 700 to 800ma in 2A Trans…900 to 998ma in 3A trans…
New transformer also showing same results.
Even i not make any complex circuits…simple rectifier only…to battery charge…
What should i do sir….
Help me sir
Kesav, check it again with your meter on the AC 10 amp range directly across the transformer wires, a 2 ampere trafo cannot produce 6 am or 9amp.
while charging your battery connect a 12V motorcycle headlamp bulb in series with the positive wire…if this lamp glows brightly initially while charging then your battery might be OK and charging normally, if not then your battery could be faulty…