In this post I have explained how to build a simple white noise generator circuit which can be subsequently filtered to generate the pink noise output.
If you hear to the white noise or pink noise, you will find it exactly similar to the noise that we hear in FM radios in the absence of a radio station, or in TV sets showing only raster, in the no signal condition.
More information about pink noise can be studied in the following article:
https://en.wikipedia.org/wiki/Pink_noise
What is Noise
A noise is normally an unwanted element that can worsen the efficiency of any measuring instrument. Hence it may appear weird that any user would require the generation of such noise, however you may find this to be quite normal.
Noise generators are quite frequently accustomed to introduce noise in radio-frequency amplifiers so that it enables the user to diagnose the amplifier's low signal efficiency.
Noise generation are also found useful for checking sound systems, and like a random signal generator while introducing wind-like sound effects in music outputs. You will find a couple of widely used noise generator characteristics, which are 'pink noise' and 'white noise'.
What is White Noise
White noise is called by this name because it possesses identical noise strength in equivalent bandwidths within the entire frequency range in question. Therefore, for instance, a white noise source might possess equal energy inside the 100 to 200 Hz frequency bands upto the band of 5000 to 5100 Hz.
When the white noise goes through a filtration process or a modification, it is referred to as colored noise or, usually to be more precise it is referred to as the 'pink' or 'grey' noise.
What is Pink Noise
The definition of pink noise is usually restricted to the noise characteristic which includes identical energy per percentage change in bandwidth. For instance when a genuine pink noise is considered, the energy between 100 Hz and 200 Hz must be identical to that between 5000 Hz and 10,000 Hz (a change of 100% in each of the scenarios).
Pink noise as a result seems to possess a high degree of bass frequency compared to what the white noise may have.
Hearing the pink noise might appear a lot more consistent and stable, during the testing process.
In order to convert white noise to pink noise, it needs to go through a filtering process which causes its output level to decrease by 3 dB per octave or by 10 dB per decade, as the frequency is increased.
How the Circuit Works
Referring to the pink noise generator circuit above, the transistor Q1 can be actually seen configured like a zener diode. The typical base-emitter junction wiring can be seen reverse-biased which gets into a zener break down situation at approximately 7 to 8 volts.
The Q1 zener noise current passes to the Q2 base, causing the generation of around 150 millivolts white noise at the output .
This `zener' configuration, no only works like a noise source, but also does the job of biasing Q2 effectively, and the Q2 noise output is applied straight to the White Noise output. To be able to transform the white noise to pink it would need to go through a filtering process, that gives a 3 dB cut per octave as the frequency is raised.
A normal RC network may not be appropriate for implementing like a individual RC stage for getting a cut of 6 dB per octave. For this reason a unique resistor Rs and capacitor Cs circuitry becomes necessary for approximating the intended 3 dB-per-octave slope.
Because this kind of a filter is able to produce a high level of attenuation of the noise, an amplifier become necessary in order to restore the output level.
For this exact reason the transistor Q3 is wired like an amplifier with the pink noise filter linked as a feedback network across the collector and base.
This enables you to get the necessary quality through the control of the gain-versus-frequency characteristics of the transistor. In this way we are able to get the required pink noise from the output of transistor Q3, which is then supplied to the indicated output socket of the circuit.
Using a Single Transistor
A simple white and pink noise generator could be constructed with the help of a single transistor and a Zener diode. The 10 volt Zener serves like the noise source and it furthermore stabilizes the operating level of the transistor.
Putting a capacitor C2 at the indicated position will convert the output from 'white' noise to 'pink' noise. Using the specified components and the supply input, the white noise level of output voltage will be around 15V, and the pink noise level of output voltage around 14.5 V. The transistor could be a BC547 or any other similar small signal transistors can also work fine.